Zultys MX250 Скачать руководство пользователя страница 19

Страница: 19 / 62

3. Hardware

3.4.2.3

Analog 50-Pin Telco Pin Assignment

The FXO and FXS interface boards have a 50-pin telco receptacle (female) for connecting analog

circuits to the MX250. Figure 3-6 shows the pin placement on the telco connector of the FXS and

FXO cards. Figure 3-7 shows the function assignment of each pin.

3.4.3

PCM (T1 and E1)

3.4.3.1

Usage

The MX250 supports up to two PCM cards through the interface slots. Each card has two

full-duplex circuits which can be configured for either T1 (1.544 Mb/s) or E1 (2.048 Mb/s). Each

circuit uses one of several supported PSTN or IP WAN protocols. The circuit type and protocol

for each circuit are configured through the MX Administrator software.

Pin

Signal Name

Abbreviation

(not connected)

—

(not connected)

—

Ring 1

Tip 1

(not connected)

—

(not connected)

—

Figure 3-5

Pin Description of the Analog RJ12 Connector

Figure 3-6

Pin Assignment of a 50-pin Telco Connector on FXO or FXS Card

Pin

Signal Name

Abbreviation

1 to 8

Tips for circuit 1 to 8

T1 to T8

26 to 33

Ring for circuit 1 to 8

R1 to R8

9 to 25

Unconnected

34 to 50

Unconnected

Figure 3-7

Pin Description of 50-pin Telco Connector

Содержание MX250































































Результаты поиска

Содержание MX250

Отзывы:

Похожие инструкции для MX250

Бренды по названию

Популярные бренды

Zultys MX250, Руководство по оборудованию

Результаты поиска

Содержание MX250

Отзывы:

Похожие инструкции для MX250

Бренды по названию

Популярные бренды