Zoom FIRE-36 Скачать руководство пользователя страница 26

 

4

 

ZOOM FIRE-36M

1.

 

With the level knobs on the rear panel turned fully down, connect the recorder, mixer, or other 
external device to the RECORDING OUT jack.

 

For information on how to connect your instrument and how to use the front panel controls, see the FIRE-
36 manual.

 

* If you plug a pair of headphones into the [PHONES] jack on the front panel, the speaker is cut off and the

mics will pick up no sound and therefore deliver almost no signal.

 

2.

 

Adjust the [MASTER] knob on the FIRE-36M to obtain a suitable volume.

 

* If the volume setting is too high or too low, the mics will not produce a proper signal. Start with the

[MASTER] knob in the center (12 o'clock) position and make adjustments as required by the playing
environment.

* Depending on the guitar and the amplifier settings, the output from the power amplifier and speaker may

be distorted. The sound picked up by the mics may also be unpleasant in such a case, but this is not a
defect.

 

3.

 

Adjust the [LINE LEVEL], [MIC 1 LEVEL] and [MIC 2 LEVEL] knobs to obtain the desired balance 
between the line signal and the mic signals.  

 

The controls should be turned up fairly high, but not so high that clipping in the input stage of the
connected equipment occurs.

 

* The [MIC LEVEL] control has a wide adjustment range to allow for the considerable volume changes of

the speaker. Adjust the control frequently to match the speaker volume.

* Also make input level adjustments at the connected device, as necessary.

 

■ 

 

Troubleshooting

 

 

No mic signal can be heard  

 

• Is something connected to the front panel [PHONES] jack?
• Are the [MIC 1 LEVEL] and [MIC 2 LEVEL] knobs on the rear panel turned up to an adequate position?
• The mic signal has no effect on the output from the speaker.

 

 

Mic signal is distorted

 

• Is the front panel [MASTER] knob turned up too high?
• Has the input level been adjusted properly at the connected device?
• Try adjusting the [MIC 1 LEVEL] and [MIC 2 LEVEL] knobs.

 

 

Other sound is heard together with the mic signal

 

The mics also pick up ambient sound. Perform monitoring in a quiet location.

 

■ 

 

Specifications

 

Microphone

 

2 x Omnidirectional condenser microphones

 

Output

Headphone output

 

Standard stereo phone jack
80 mW into 32-ohm load

 

Balanced output

 

XLR-3-32 jack
Rated output level +4dBm with output load impedance 10 kilohms or more

 

Unbalanced output

 

Standard stereo phone jack
Rated output level +4dBm with output load impedance 10 kilohms or more

 

*  0 dBm = 0.775 Vrms
*  Design and specifications are subject to change without notice.

 

English

 

ZOOM FIRE-36M Supplemental Manual

Fire36m.fm 4 ページ 2004年7月7日 水曜日 午前10時39分

Содержание FIRE-36



























Отзывы: