Installation and Wiring
1. Open the Control Unit and the Door
Panel from the package.
2. Mount and connect the Control
Unit and the Door Panels (both the
left and the right door panels) with
the nuts and then tighten the
screws as shown in the image.
3. Insert the probe-lines of the left
and right door panels to the
corresponding sockets on the
mainboard.
4. Lift the walk through temperature
detector to the vertical position and
move it to the required place.
5. Plug-in the power cable.
Left
door panel
Right
door panel
Used for wiring the temperature probe
on the right door panel.
2
3Pin terminal (J15 ):
Used for wiring the alarm zone LED of the
left door panel.
3
2Pin terminal
Used for wiring the alarm zone LED of the
right door panel.
4
2Pin terminal
Parameters
Infrared temperature sensor
Medical infrared temperature sensor
(High accuracy of IR temperature acquisition
module, single probe round structure)
Temperature measurement method
Optimal detection distance
By detecting body temperature of forehead
or wrist
50mm-100mm
Number of temperature probes
1 (optionally equipped with multiple probes,
consistent performance)
Probe mounting height
1.5m from the ground (customizable)
Temperature measurement error
Detection time
Temperature measurement range
Multiple measurement interval
Display method
Alarm method
Power supply
Rated power
Working temperature
Shell size(H*W*D)
Channel size(H*W*D)
Packing size (door panel)(H*W*D)
Packing size (main box)(H*W*D)
Weight
±0.5
°C
≦
1s
30
°C
~ 40°C
2s
Digital tube
Audible and visual alarm
AC100-220V, 50 / 60Hz
≦
40W
16
°C -
38
°C
2200 * 820 * 580(mm)
2200 * 710 * 580(mm)
2280 * 260* 580(mm)
780* 390* 250(mm) * 1tcn
Around 70kg
Using Instructions
Please place the person's forehead or wrist in front of the Infrared
temperature probe about 5-10cm away, after the person enters the
detection area whose temperature is to be measured. Upon completion of
the test, a beep sound is heard which indicates that the temperature of
the individual is normal.
When the temperature in the temperature display area is 37.3 °C or higher,
the security gate will sound "beep, beep, beep" with sound-light warnings
indicating that the temperature of the individual is detected abnormal
and is restricted to pass through. More observations and tests will be
conducted on the individual to verify their health status.
Precautions for Use
1. ZK-D3180S walk through temperature detector is recommended to be
used in an indoor environment, avoid using in strong light and high
temperature environment.
2. The temperature measurement point infrared probe is 1.5 meters above
the ground. If the height is less than 1.5 meters, the forehead cannot be
detected. The temperature can be detected by the wrist. You can also
customize the required distance and height when purchasing the
product to meet the needs of the place of use.
3. The inclination angle of the temperature measuring probe is 15 degrees.
When passing the security gate, the passer normally passes near the
temperature measuring probe, de ects his head slightly, and points his
forehead to the temperature measuring probe to about 15cm for
detection.
4. To assist the epidemic prevention temperature measurement work, it is
suggested to assign a staff member to manage the temperature
measurement at the entrance of the channel, guide the operation of
the tested personnel, and ensure the accuracy of the temperature
measurement.
5. Do not disassemble the control units except the professional technician.
1
2
3
4
Used for wiring the infrared distance sensor
on the right door panel.
1
4Pin terminal (J 4 ):
Note:
1.
Temperature measurement data is for
reference only, not for medical use. This
product is not suit for environment with
strong light or high temperature. It is
recommended to use this product indoors
without wind.
2. Once you turn on the device or change an
application environment, please leave it
for 10-15 minutes to calibrate the accuracy.
3.
During use, please place the person's
forehead or wrist align the infrared
temperature probe and cover the distance
sensor.
