background image

 

 

Chapter 2 The Installation of the Product 

2.1 Installation notes 

1)

 

It is recommended that the swing barrier turnstile be installed on a horizontal solid platform 
with 50mm to 100mm in height. 

2)

 

It is recommended that the swing barrier turnstile should not be used in corrosive environment.   

3)

 

Make sure the protective earth wire of the system is reliably connected to avoid personal injuries 
or other accidents. 

4)

 

After installation, check whether connection is reliable at the connecting points of the 
protective earth wire, at the connector assemblies and wiring points of the circuits, as well as at 
each movable part of the swing barrier turnstile. Any loose nuts, screws and other fasteners 
should be tightened in time to avoid swing barrier turnstile failures caused by long-time 
operations. 

2.2 Installation position of the swing barrier turnstile 

The installation position depends on the size of the swing barrier.If the swing barrier turnstile is 
installed near a wall, a distance of 100mm between the swing barrier turnstile and the wall needs to 
be reserved for ease of installing the device. The SBT1000S swing barrier turnstile may form a 
channel, or form two channels with a SBT1000S swing barrier turnstile,as shown in figure 2-2A; 

 

Figure2-2A SBT1000S Single channel and dual channel 

2.3 Cables installation and fixation 

For the outlets of the concealed cables, please refer to the drawing showing the mounting holes. 
The input voltage for this swing barrier turnstile is AC100-120V/200-240V. The PVC conduits are 
buried 100mm under the ground, with the height of the exposed part about exceeding 100mm. In 
addition, the conduit outlet is bent back to prevent ingress of water into the conduit.   
SBT1000S installation holes and cabling positions as shown in Figure 2-3A.   

Содержание SBT1000S












Отзывы:

Похожие инструкции для SBT1000S