OUTPUT 2
OUTPUT 1
3VDC SET RST
INPUT 1 INPUT 2
LED
ENABLE
PO
WER
INPUT
1
INPUT
2
FAULT
CLOSED
0
1
1
64
F-SAFE
N/O COM N/C
SERIAL NO
LOGON
IP- IP+ IP- IP+
3VDC SET RST
N/O COM N/C
EXPAN1
EXPAN2
RELA
Y ON
RELA
Y ON
2
4
8
16
32
ANTENNA
KEEP CABLES AWAY FROM THIS AREA
LR6
AA
LR6
AA
LR6
AA
LR6
AA
LR6
AA
LR6
AA
Figure 2
Relay
LEDs
Input
LEDs
LED
Enable
Button
Input Fault LEDs:-
Each input contact has a yellow fault LED associated with
it. If the input is in a fault condition the LED will be
illuminated.
Input Switch Closed LEDs:-
Each input contact has a red switch closed LED
associated with it. If the input is closed the LED will be
illuminated.
Output connection Wiring
The Ziton I/O unit has clean contact relay outputs
capable of switching 2A @ 24V DC. The location of the
output connections are shown in Figure 2.
0
Common and normally closed connected
1
Common and normally open connected
On power up the relay outputs will be reset to output bit
state 0.
Output fail to safe mode
This function is enabled/disabled by loop address switch
8. Switch 8 to the 1 position enables this mode of
operation and switch 8 to the 0 position disables the
mode. As default this mode is disabled.
When the function is enabled, the relay outputs will
assume the output bit state 0 in the event of:-
• Communication loss to the Ziton loop interface
• Failure of any battery pack
Note: Switches 1 to 7 are not used
Output bit
state
Relay State
N/O
INPUT
CONNECTION
20k
EOL
IP -
IP +
4K7
INPUT 1
Figure 3
20K resistor colour coded as red / black / orange
4K7 resistor colour coded as yellow / violet / red
20K = normal condition
3K8 = alarm condition
Open circuit = tamper condition
Short circuit = tamper condition
Functional testing
When polled by a compatible panel, the Ziton I/O unit, in
its normal condition will return an analogue value of 90*.
Input open (normal condition) 90* N/A 0
Input closed (alarm condition) 213 N/A 1
Open circuit N/A 118 N/A
Short circuit N/A 118 N/A
Tamper N/A 181 N/A
* The Slot 5 analogue value for the open input conditions
are shown in relation to the device’s signal strength.
Therefore these can vary between analogue value 90, 85,
80 or 75.
Fault condition
Analogue value
Input
status
Slot 5 Slot 6
Operating
Temperature
-10 to +50°C
Storage
Temperature
-20 to +60°C
Humidity
Up to 95% non-condensing
Supply
6x AA Alkaline (Panasonic LR6AD
Powerline / Varta 4006 Industrial)
IP Rating
IP65
Output Rating
2A @ 24V DC
Operating
Frequencies
868 MHz
Output Transmitter
Power
Variable 0-14 dBm
Dimensions
120mm (H) 240mm (W) 50mm (D)
Weight
0.60kg
Regulatory information
Manufacturer
EMS Ltd.
Technology House, Sea Street,
Herne Bay, Kent, CT6 8JZ,
United
Kingdom
Year of
manufacture
See serial number label inside unit
Certification
Certification body
CPR Certificate
DOP
0359-CPR-0171
Approved to
EN54-18
EN54-25
Application
Indoor use only
European Union
directives
EMS declares that the radio
equipment
type
Ziton Wireless
Input / Output Unit is in compliance
with Directive 2014/53/EU. The full
text of the EU declaration of
conformity is available at the
following internet address:
www.utcfssecurityproducts.eu/dop/
2012/19/EU (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in the European
Union. For proper recycling, return
this product to your local supplier
upon purchase of equivalent new
equipment, or dispose of it at
designated collection points. For
more information see
www.recyclethis.info
Contact information
For contact information, see www.utcfireandsecurity.com
Input
connections
Output
connections
0359
12
Input connection wiring
The location of the Ziton I/O unit’s input connections are
shown in Figure 2. Connection details are shown in
Figure 3.
