background image

 

Chapter 1: Maintenance 

 

ZP3-ECU Extinguishing Control Unit Maintenance Manual 

Preventive maintenance 

Preventive maintenance is divided into the following categories: 
•  Daily checks 
•  Weekly maintenance 
•  Quarterly maintenance 
The daily and weekly maintenance tasks require no technical expertise and 

should be carried out by the panel operator. 

Daily 

The ECU must remain clean at all times. Perform the following: 
•  Clean the outer surface of the unit to remove any excess dust using a damp 

cloth. 

•  Check for correct and smooth operation of the key switches. Lubricate sticky 

key switches if required using 2 or 3 drops of a general purpose lubricant (for 

example 3 in 1 oil). 

Weekly 

•  Check any reports sent from the ECU to the fire alarm control panel. Under 

normal conditions no abnormal reports should be detected. 

•  Check the front panel of the ECU and any status units. Only the POWER ON 

and Automatic/Manual LEDs should be illuminated. 

•  Test the function of the Automatic/Manual key switch by operating the switch. 

Check that the printer (if available) on the fire alarm control panel indicates 

the change in switch position. 

•  Restore the system to previous configuration. 
•  Log the test in the system log. 

Quarterly maintenance 

Quarterly maintenance must be carried out by suitably trained personnel. Such 

personnel may be direct employees of the company, or may be contracted from 

the maintenance company responsible for servicing. 
Quarterly maintenance is designed to pre-empt any problems that may arise and 

to check that the system is functioning to its installation specifications. The 

services should be arranged through a maintenance contract with a servicing 

company. This agreement should specify how to contact the service company 

and how they can access the premises. 
Repair services should be available within 24 hours. For premises in continuous 

use, an engineer should be on call at all times. The servicing company should 

have engineers trained in servicing Ziton equipment. The owner of the fire alarm 

system is responsible for ensuring that the company contracted is competent to 

carry out the work. 

Содержание ZP3-ECU

































Отзывы: