background image

5

INSTALLATION INSTRUCTIONS & USER MANUAL 

210005 V2.00 AUG 2017 - ZIP APIII/5-15(OB)

TECHNICAL SUPPORT

 TEL: 0345 6 005 005 EMAIL: SERVICE@ZIPINDUSTRIES .CO.UK   

WWW.ZIPWATER.CO.UK

(1) EU Regulation 812/2013;EN 50440
(2) Temperature control ‘e’ setting corresponds to approx. 41°C for models AP3/05/0B, AP3/05 or 35°C for models AP3/10/OB, AP3/10, AP3/15/OB, AP3/15.

Safety Information

WARNINGS

 

•   Installation, commissioning and maintenance of this appliance must only be carried 

out by a competent installer who will then be responsible for adhering to all relevant 
standards and regulations.

•   The appliance must be disconnected from mains power supply before carrying out 

any work involving live circuits.

•   The appliance must be permanently connected to the supply through an isolating switch 

with a contact separation of at least 3mm in all poles and be protected by a suitably rated 
RCD.

•   To protect the appliance, an MCB (miniature circuit breaker) or cartridge fuse must be 

fitted with a rating suitable for the nomi nal current of the appliance.

•   The cross sectional area of the connection cable must be appropriate for the power rating 

and location of the appliance. See Technical data, page 4. 

•   The connecting cable must be adequately secured.
•   

 This appliance must be earthed at all times.

•   Check that the power supply is switched off prior to electrical connection.
•   The appliance, its wiring and piping must not be modified in any way.
•   In case of malfunction isolate the power supply immediately. In case of leaks also isolate 

the water supply. Repairs must only be carried out by a competent person.

•   Temperatures in excess of approximately 43°C are perceived as hot, especially by children, 

and may cause a feeling of burning. 

SAFETY INFORMATION

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, 
could result in death and/or serious injury and/or property 
damage.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, 
may result in property damage. 

IMPORTANT:

PLEASE READ THESE INSTRUCTIONS CAREFULLY. 
NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT 
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO 
MAY CAUSE DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. RETAIN 
THESE INSTRUCTIONS FOR FUTURE USE.

Содержание AQUAPOINT III AP3/05





















Отзывы: