background image

 

4

Shielded interface cables must be used in order to comply with emission limits. 
 
This EUT is incompliance with SAR for general population /uncontrolled 
exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance 
with the measurement methods and procedures specified in OET Bulletin 65 
Supplement C. 
 

 

CAUTION

 

1. The antenna(s) used for this transmitter must be fixed-mounted on outdoor 

permanent structures with a separation distance of at least 2 meters from 
all persons and must not be co-located or operating in conjunction with any 
other antenna or transmitter. Users and installers must be provided with 
antenna installation instructions and transmitter operating conditions for 
satisfying RF exposure compliance. 

 
2. This Transmitter must not be co-located or operating in conjunction with any 

other antenna or transmitter. 

 
3. This equipment is only allowed to be professionally installed. 

 

 

 

 

 

 

 

 

 

 

 

 

This equipment has been tested and found to comply with the limits for a class B digital device, 

pursuant to part 15 of the FCC rules. These limits are designed to provide to provide reasonable 

protection against harmful interference in a residential installation. This equipment generates, uses and 

can radiate radio frequency energy and, if not installed and used in accordance with the installation. , 

May cause harmful interference to radio communication. However, there is no guarantee that 

interference

Will not occur in a particular installation. if this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna

-Increase the separation between the equipment and receiver

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

-Consult the dealer or an experienced radio / TV technician for help

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled 

environment. This equipment should be installed and operated with a minimum distance of 20 

centimeters between the radiator and your body. 

Содержание RAD 500














































Отзывы: