manualshive.com logo in svg

Zhone ETHX-2214-DS3, Руководство по установке

Поделиться
Скачать
Zhone ETHX-2214-DS3 Скачать руководство пользователя страница 19

 

 

19 

Command Line Interface 

The network extender can be managed with a Command Line Interface (CLI) through 
either a direct PC to COM (Communication) Port connection or from a remote network 
connection via Telnet. 

 
CLI System Requirements 

 

Straight-Through 8-Pin Modular Ethernet Cable – Required for establishing a 
direct connection from the COM port to a DB9 adapter. 

 

DB9 Female to 8-Pin Modular Male Adapter – Required for conversion of your 
PC's RS232 serial port for use with the Ethernet cable.  

 

Terminal Emulation Program – Required for running the CLI over a direct 
connection. The program must emulate a VT100 terminal. 

 

Telnet Client – Required for remote management with the CLI. Microsoft Windows 
Operating Systems (98, 2000, NT, and XP) include a Telnet client which is run 
using the Windows command prompt (cmd.exe). If you are using an operating 
system other than Windows, you may need to install a Telnet client. 

 
Connecting a PC Directly 

Initial configuration using the CLI requires a direct physical connection from your PC to 
the COM port of the network extender you are configuring. After an initial configuration 
is completed, it is recommended that subsequent configurations be managed through 
the web interface. 
 

 

Procedure 

1.  Plug a DB9 to 8-pin modular adapter into the RS232 serial port on your PC. See 

DB9 to 8-Pin Modular Adapter Pin Assignments on page 22. 

2.  Connect one end of a straight-through Ethernet cable into the DB9 to 8-pin 

modular adapter, and the other end of the cable into the COM port on the face of 
the network extender. 

Содержание ETHX-2214-DS3





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды