background image

 

 

Welcome 

Thank you for purchasing our network camera! 

This quick start guide is designed to be a reference tool for your system.  

Please keep this start guide well for future reference. 

Please open the accessory bag to check the items one by one in accordance with the list below. 

Contact your local retailer ASAP if something is missing or damaged in the bag. 

 

Before your operation please read the following instructions carefully.  

1

Electrical safety 

All installation and operation here should conform to your local electrical safety codes.  

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited 

power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction) 

Please 

note: Do not connect two power supplying sources to the device at the same time; it may result 

in device damage! The product must be grounded to reduce the risk of electronic shock. 

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling 

or installation.  

We are not liable for any problems caused by unauthorized modification or attempted repair. 

 

2

Transportation security 

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and 

installation. 

 

3

Installation 

Do not apply power to the camera before completing installation.  

Please install the proper power cut-off device during the installation connection. 

Always follow the instruction guide the manufacturer recommended. 

 

4

Qualified engineers needed 

 

All the examination and repair work should be done by the qualified service engineers.   

We are not liable for any problems caused by unauthorized modifications or attempted repair. 

 

5

Environment 

This series network camera should be installed in a cool, dry place away from direct sunlight, 

inflammable, explosive substances and etc. 

Please keep it away from the electromagnetic radiation object and environment. 

Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device. 

Otherwise it may result in CCD (CMOS) optical component damage. 

Please keep the sound ventilation.  

Do not allow the water and other liquid falling into the camera. 

Содержание DH-IPC-HFW5421E-Z















Отзывы: