Zgonc YELLOW GARDENLINE YGL N.G. 5351, Перевод оригинального руководства пользователя

Страница: 37 / 48

37 GB
m
WARNING
Fumes from fuel and solvents can cause explosions.
After repairs and maintenance work, re-attach the safety
devices to the machine.
Ensure the machine is operational, in particular, check
the fuel system for leak-tightness.
Always clear the motor‘s cooling fins of contamination.
m
DANGER
m
The manufacturer of this equipment shall be not liable
to the applicable Product Liability Act for damages aris-
ing in this device or this unit at:
• Installation and replacement of non-original spare
parts,
• Removal or alteration of safety components.
5.7 Operating instructions
m Important notices
1)
Turn off the motor if the saw comes in contact with
foreign objects. Check the saw and, if applicable,
repair it.
2)
Protect the chain from dirt and sand. Even small
quantities of dirt can quickly make the chain blunt
and increase the risk of kickback.
3)
Start by cutting up smaller logs to practise in order
to get a feel for the device, before attempting diffi -
cult tasks.
4)
Activate the throttle at maximum, before starting
sawing.
5)
Press the casing of the chainsaw against the log
when starting sawing.
6)
Run the device at full throttle throughout the whole
sawing process.
7)
Let the saw do the work. Only use slight downwards
pressure.
8)
Release the throttle as soon as you have finished
your work so the motor runs idle. If you let the ma-
chine run at full throttle without load, there will be
unnecessary wear and tear.
9)
So that you do not lose control of the device after
the chain exits the wood, you should not apply any
pressure to the saw towards the end of the cut.
10)
Check after starting the idle setting. The cutting
blade must be stationary during idling. Wenn die
Schneideinrichtung im Leerlauf läuft, muss die Leer-
laufdrehzahl gesenkt werden (siehe „Einstellen der
Leerlaufdrehzahl“).
11)
Turn off the device before putting it down.
Felling trees - only with relevant training
m
CAUTION
Watch out for broken or dead branches which may fall
down during sawing and which could cause severe inju-
ries. Do not saw close to buildings or power lines if you
do not know in which direction the felled tree will fall. Do
not work at night because you can see less well, or dur-
ing rain, snow and storms because the direction in which
the tree will fall cannot be anticipated.
• Plan your work with the chainsaw in advance.
• The working environment around the tree should be
cleared so you have secure footing.
• The machine operator should always be positioned at
a higher level in the working area because the tree will
probably roll or slide down after felling.
The following conditions can influence the tree‘s
falling direction:
• Wind direction and speed
• Leaning of the tree - The leaning direction cannot al-
ways be recognised because of uneven or sloping
ground. Determine the leaning direction of the tree
using a plumb line or a level.
• Branches growing (and therefore weight) only on one
side
• Surrounding trees or obstacles
Look out for destroyed or decayed parts of the tree.
If the trunk is decayed, it can suddenly break and fall on
you. Make sure there is sufficient space for the falling
tree. Keep a distance of 2½ tree lengths to the next per-
son or other objects. The sound of the motor can drown
out warning cries.
Remove dirt, stones, loose bark, nails, brackets and wire
from the sawing area.
m
Ensure you have a free escape route (Fig. A)
Position 1: Escape route
Position 2: Falling direction of the tree
Felling of large trees - only with relevant training
(from 15cm diameter)
The undercutting method is used for felling large trees.
For this, a wedge is cut out from the side of the tree ac-
cording to the required falling direction. After the drop-
ping cut has been made on the other side of the tree, it
will fall in the direction of the wedge cut.
m
NOTICE
If the tree has large prop/buttress roots, these should be
removed before the wedge is cut. If the saw is used for
removing the prop/buttress roots, the saw-chain should
not touch the ground so the chain does not become
blunt.