Zetor Proxima 100 2012 Скачать руководство пользователя страница 113

Страница: 113 / 214

112

WHEEL TREAD CHANGE

C506

SETTING THE WHEEL TOE-IN AT TRACTORS WITHOUT FRONT DRIVING AXLE

Note:

As standard, the tractors are provided with hydrostatic steering.

−

Set the wheels symmetrically with the longitudinal axis of tractor.

−

In the front in horizontal plane of wheel axes measure the distance between rims.
Mark the measuring point.

−

Drive the tractor so that the marked points would be in the rear in horizontal plane
of wheel axes (turning by 180°) and again measure the distance between the
marked points.

−

Shift out the piston rod of the cylinder at 145,5

−

Loosen the nuts (2,3) and by turning the rod (4) adjust the toe-in at the required
value (measure at the rime side).

−

Tighten the lock nuts of the heads of ball joints by torque 122 - 136 Nm. Upper
surfaces of heads must be parallel.

Содержание Proxima 100 2012























































































































































































































Результаты поиска

Содержание Proxima 100 2012

Отзывы:

Zetor Proxima 100 2012, Руководство оператора, Страница: 113 / 214

Результаты поиска

Содержание Proxima 100 2012

Отзывы: