Please take a few moments to check all pack contents listed.
Requires 2 person assembly.
Tools required: Corded / Cordless Drill, Pozi-drive Bit / Screwdriver, Socket Set,
Hammer. 3mm Drill Bit, required in order for you to drill all screw holes before
construction.
Miami Swing is now complete.
1.
Position 1no Front Leg A1 and Back Right Leg A3 either side of Beam B (Fig.1a), align bolt
holes and attach using 1no 140mm Bolt, washer & nut (Fig.1b). Do not fully tighten at this
stage. Repeat procedure for the remaining Front Leg A2 and Back Leg A4 at the other end of
Beam B.
2.
Position Horizontal Short Brace C (Fig.2a) and Horizontal Long Brace D (Fig.2b) onto Legs,
align bolt holes and insert 8no 100mm Bolts – 4no per horizontal brace. Repeat procedure for
the remaining braces and Legs.
3.
Turn over the Legs/Beam Assembly (Fig.3a), attach washers and nuts and fully tighten
(Fig.3b).
4.
Attach Diagonal Brace E to Beam B using 2no 90mm Bolts, washers & nuts and fully tighten
(Fig.4a). Raise Leg Assembly, align Diagonal Brace E & Horizontal Short Brace C bolt holes
and fix in position using 1no 80mm Bolt, washer & nut (Fig.4b). Fully tighten all nuts at this
stage. Repeat procedure with the remaining Diagonal Brace E at the other end of Beam B
(Fig.4c).
5.
Insert 2no 150mm Eye Bolts into the Beam B (Fig.5) and secure using washers and nuts.
6.
Locate half lap joints of Seat Back F into half lap joints of Seat G and fix in position using 6no
45mm Bolts, washers & nuts – 2no per joint (Fig.6b)
7.
Locate the Armrest Support H dowels into the Armrest J2 holes (Fig.7a) and fix in position
using 1no 60mm Screw (Fig.7b). Repeat procedure for the remaining Armrest Support H and
Armrest J1.
8.
Attach Armrest Assembly to Seat Assembly using 2no 115mm Eye Bolts as shown in Figs 8a &
8b. Repeat procedure for the remaining Arm Assembly.
9.
Hook 1no Short Chain & 1no Long Chain onto Large Karabiner ensuring Short Chain is at the
back (Fig.9a). Repeat procedure for remaining chains. Attach Short Chain to the back of the
Seat Assembly (Fig.9b) and Long Chain to the front of the Seat Assembly (Fig.9c) using 2no
Small Karabiners. Repeat procedure for remaining Chains.
10.
Locate Shelves K onto Long Braces D (Fig.10).
11.
Position Slats Support M with bolt hole (circled) rearmost. Align with bolt hole in Back Leg A3
and fix using 1no 110mm bolt. (Figs. 11a & 11b) Repeat procedure to attach remaining Slat
Support M to Back Leg A4.
Ensure both Slats Supports M are inclined equally and fix into Front Legs A1 & A2 using 2no
100mm screws (1no per leg). (Fig. 11c)
12.
Equally space Canopy Slats L onto Slats Supports M, ensure equal overhang at both ends and
fix first and last slats using 4no 40mm screws (2no per slat, 1no per end) and all intermediate
slats using 60mm screws. (Figs. 12a, 12b & 12c)
13.
Insert (rotate and flex simultaneously) Centre Batten N and once fully central attach to slats
using 16no 30mm Screws, (1no per canopy slat). (Figs. 13a, 13b & 13c).
