Zephyr Tempest II AK7500ASX Скачать руководство пользователя страница 20

Страница: 20 / 23

www.zephyronline.com

REPLACING LIGHT BULBS

CAUTION: Light bulb becomes extremely hot when turned on.

DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns.

Make sure all power is turned off and bulbs are not hot.

Remove by turning bulb counter clockwise.

Note:

Bulb does not unscrew; it turns 60 degrees, stops and

falls out.

If bulbs are diffi cult to turn due to prolonged use, fi rmly attach a glass suction cup approximately the
diameter of the bulb or use a rubber/latex glove and turn counter clockwise.

Replacement bulbs are available at specialty lighting stores. Purchase type MR16 (GU-10) 35W halogen.

For Zephyr part numbers please turn to page 20 of the manual.

Maintenance –

Lights

Содержание Tempest II AK7500ASX
























Результаты поиска

Содержание Tempest II AK7500ASX

Отзывы:

Похожие инструкции для Tempest II AK7500ASX

Бренды по названию

Популярные бренды

Zephyr Tempest II AK7500ASX, Инструкция по использованию, уходу и установке

Результаты поиска

Содержание Tempest II AK7500ASX

Отзывы:

Похожие инструкции для Tempest II AK7500ASX

Бренды по названию

Популярные бренды