Zephyr Essentials ZAN-E30CBS, Инструкция по использованию, уходу и установке

Страница: 14 / 54

12
www.zephyronline.com
0HDVXUHIURPUDQJHWRSWRKRRGERWWRPDQGPDUNOLQH$
´PLQLPXPIURPUDQJHWRS
3OXPDQGPDUNFHQWHUOLQH
0DUNKRRGKHLJKWOLQH%
ZAN : 18-7/16” from line A
ZSA : 9-1/2” from line A
ZRV : 15-7/8” from line A
ZRO : 11-3/8 from line A
0DUNPRXQWLQJVSUHDGIURP&/
ZAN : 8-7/8” on line B
ZSA : 9-7/8” on line B
ZRV : 8-15/16” on line B
ZRO : 12-5/8” on line B
)DVWHQ0[´VFUHZVLQWRVWXGVRQOLQH%EXWGRQRWWLJKWHQDOO
the way. Note: Wood blocking may need to be added behind the
drywall if no studs are present. Wall anchors may also be used
but check local codes for compliance. Failure to use suitable wall
anchors and screws to hold the weight of the hood could result
in personal injury or damage to the cooking surface or counter.
5HPRYHWKHDOXPLQXPPHVK¿OWHUV
7. Hang hood onto the mounting screws and hand tighten each screw.
)LJ$
&HQWHUDQGDWWDFKGXFWFRYHUPRXQWLQJEUDFNHWWRZDOOMXVWEHORZWKH
FHLOLQJRUVRႈWXVLQJ0[´VFUHZV
,QVWDOOHOHFWULFDODQGGXFWZRUN6HDOGXFWZRUNZLWKDOXPLQXPGXFW
tape.
3RZHUXSKRRGDQGFKHFNIRUOHDNVDURXQGGXFWWDSH
3ODFHWHOHVFRSLFGXFWFRYHUVRQWRKRRGDQGH[WHQGLQQHUWRSGXFW
FRYHUXSZDUGVDQGVHFXUHWRGXFWFRYHUEUDFNHWXVLQJ0[
VFUHZV5HLQVWDOOPHVK¿OWHUV
12. ZRV : Lilft glass canopy and place on top of hood body, secure glass
FDQRS\WRKRRGERG\E\[DQGWLJKWHQVFUHZV
* If using hood in recirculating mode you must secure the air diverter
SODWHRQWRZDOOEHIRUHLQVWDOOLQJGXFWZRUNDQGGXFWFRYHUV<RXZLOO
DOVRQHHGWRLQVWDOOFKDUFRDO¿OWHUVDQGEUDFNHWV7XUQWRSDJHIRU
more details.
26” min.
CAUTION: At least two installers are required
due to the weight and size of the hood.
!
WARNING: Electrical wiring must be done by a qualified person(s) in
accordance with all applicable codes and standards. This range hood must be
properly grounded. Turn off electrical power at service entrance before wiring.
!
Cable Lock
Cable Lock
$FDEOHORFNLQJFRQQHFWRUQRWVXSSOLHGPLJKWEHUHTXLUHGE\ORFDO
FRGHV&KHFNZLWKORFDOUHTXLUHPHQWVDQGFRGHVSXUFKDVHDQG
install appropriate connector if necessary.
Installation –
Mounting the Hood
FIG. A