background image

22

 Features & Controls - T

ouch Controls & 

Features

Use the high suction speed in cases of concentrated kitchen vapors.  It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in operation during cooking and for another 15 minutes after
terminating cooking.

Note:

  Hood retains last speed setting when aspiration switch is turned off.

Description of control panel:

1. Blower On/Off

By pressing 

 ,the blower is switched On and Off.

2. Speed Selection

The 3 speed levels are selected by pressing 

 to decrease and 

 to increase speed level.

The display indicates level selected.

3. Delay Off

This is used for programmed shut down of blower and lights 15 minutes after the function is activated.

Press once,a dot flashes in the lower right hand side of display 

indicating the function is on.

The hood will completely shut down in 15 minutes.

4. Lights On/Off/Dim

Switch lights On and Off by pressing 

 once.To dim lights,press and hold it in 

 for 2 seconds.

5. Advance Display Functions

6. Mood Light On/Off

This switch turns the mood lights On and Off.Press IN to turn on,press again to turn OFF.
Filters Clean Reminder (Metal):

1

5

2

6

4

3

Blower ON/OFF

Display 

(Speed Level, Delay Off Indicator, Filter Clean)

Adjust 3 Speed Levels

Mood Light ON/OFF

Lights ON/OFF/Hold to Dim

15 Min Delay Off

Содержание Cheng Padova CPA-E48ASX




























Отзывы: