background image

4

English

2. Explanation of pictorials

(1) Read owner's manual before

operating this machine.

(2) Wear head, eye and ear

protection.

(3) Warning/Attention
(4) The unit has not been

designed to provide protection
from electric shock in the
event of contact with overhead
electric lines.

If warning labels peel off or become
soiled and impossible to read, you
should contact the dealer from which
you purchased the product to order
new labels and affix them in the
required location(s).

Never remodel your machine
We won't warrant the machine, if
you use the remodeled machine or
you don't observe the proper
usage written in the manual.

WARNING

IMPORTANT

3. Symbols on the machine

For safe operation and maintenance,
symbols are carved in relief on the
machine. According to these
indications, please be careful not to
take a mistake.

(a) The port to refuel the "MIX

GASOLINE" 

Position:

FUEL TANK CAP

(b) The direction to close the choke

Position:

AIR CLEANER COVER

(c) The direction to open the choke

Position:

AIR CLEANER COVER

(d). If you turn the rod by screwdriver

follow the arrow to the "MAX"
position, the chain oil flow more,
and if you turn to the "MIN"
position, less. 

Position:

Bottom of the power unit 

中   文

(1)阅读使用说明书
(2)戴头盔、防尘眼镜和耳塞
(3)警告/注意
(4)本机不能防止由于接触到高空电

线而导致的触电现象。

警告标签污损护剥落时,请到购买本品
的商店重新订购,及时更换。

改造机器非常危险,切勿改造。
擅自改造或用于使用说明书所记载的正
确的使用目的以外的用途时,将不能享
受厂家所提供的各种保障,故请提起注
意。

为便于使用操作和保养管理,操作装置
用标志符号来表示。请按这些标志符号
进行操作,注意避免发生失误。

(a)表示使用燃料的种类为“混合汽

油”。
标志符号表示部位:燃料缸盖。

(b)表示向该符号的方向操作控制杆

时,进气门便会关闭。
标志符号表示部位:空气滤清器
的盖子

(c)表示向该符号的方向操作控制杆

时,进气门便会开通。
标志符号表示部位:空气滤清器
的盖子

(d)如果使用螺丝刀按照以下所示箭

头方向将控制杆转至“MAX(最
大)”位置,则链条油的出油量
较大。如果将控制杆转至“MIN
(最小)”位置,则链条油的出
油量较小。
标志符号表示部位:电源底部。

2. 警告标签及用法

3 操作装置符号

重   要

警   告

Содержание PSJ2300





























Отзывы: