Zenoah EXZ2610DL Скачать руководство пользователя | Manualshive

Страница: 13 / 32

background image

GB-13

G

B

EXZ2610DL

(1)

6. Set up

(BC-EX only)

INSTALLING CUTTING ATTACHMENT GUARD
FOR TRIMMER HEAD

• Attach the cutting attachment guard with the bolts

combined to the shaft tube while inserting the spacer
between the guard and the shaft tube.

INSTALLING TRIMMER HEAD

1. While locking the gear shaft, by inserting the supplied

tool into the upper holder on the angle transmission,
loosen and remove the hexagon nut (left-handed).

2. Then screw in the trimmer head to the gear shaft over

the holders. Hand-tighten it securely.

HARNESS

(1)

WARNING

ALWAYS WEAR THE PROVIDED HARNESS WHEN
USING THE MACHINE!

Always make sure the machine is hooked securely
to the harness.
If you don't, you will be unable to control the machine
safely. This can result in injury to yourself or others.
Never use a harness with a defective quick release
or any other damage.

HOW TO WEAR

1. Wear the provided harness without twisted bands, with

the hanger on your right side.

(1) Hanger

BALANCE THE UNIT

1. Hook your machine to the hanger.
2. Adjust the bands of the harness to have the blade

parallel to the ground when standing in your normal
working position to provide you most effectiveness
and comfort on operating the machine.

3. In order to prevent the hanger position to change

during operation, turn up the extra part of the band
from the buckle.

QUICK RELEASE

The harness is equipped with a "QUICK RELEASE"devise.
To release the machine from the harness in emergency
situations, please follow the procedure as explained
below.

WARNING

Make sure to check proper working of the QUICK RE-
LEASE device BEFORE operating the machine.
Make sure to hold the unit securely when using the
QUICK RELEASE.

While holding the unit by your left hand securely, press
both sides of the
buckle.

(1) Buckle

4. When correctly adjusted, check the correct working

of the harnesses' QUICK RELEASE.

«
...
11
12
13
14
15
...
»

Содержание EXZ2610DL

































Отзывы:

Нет отзывов

Похожие инструкции для EXZ2610DL

Бренд: KEENCUT Страницы: 4

Бренд: Laski Страницы: 35

Бренд: Mafell Страницы: 174

Бренд: Makita Страницы: 8

Бренд: Land Pride Страницы: 32

Бренд: Mafell Страницы: 96

Бренд: Masport Страницы: 7

Бренд: Solesbee's Страницы: 16

K650 ACTIVE III

Бренд: Partner Страницы: 24

Бренд: Poulan Pro Страницы: 38

Бренд: Rothenberger Industrial Страницы: 76

GocMakSan MG20B 220V DIGITAL

Бренд: GMS Страницы: 9

Isoturbo 5305S-30 2014

Бренд: SPEWE Страницы: 12

Isoturbo 6000L S-05

Бренд: SPEWE Страницы: 26

Бренд: Binks Страницы: 12

Бренд: Zenit Страницы: 12

Бренд: Zenoah Страницы: 32

Бренд: Tanaka Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды