background image

8

A100K10873

VSP 12-Way Batteryless Telephone System

Technical Manual

3  Installation

In a VSP system, one station MUST BE a VSP-211-L where the 

transistorized amplifier is located. This amplifier is used by all stations.

The other stations in the system can be any other VSP station type, 

depending on the requirements and environments.

3.1  Connection

All stations in a VSP system are connected in parallel, i.e. all terminals 

with the same number are linked together in all stations.

Some stations have additional terminals for station type related 

connections.

All VSP stations

General screw terminal block numbered from 1 to 16. 

Microphone line

1 (signal) and 2 (ground)

Speaker line

3 and 4 (balanced)

Station lines

5 to 16 (lines 1 to 12)

VSP-223-L station

This station has a built-in latch relay circuit for activating external 

audible and/or visible signal units. Additional terminals 17-22 are added 

for this feature.

Local 24 VDC for signal unit

17 (+24 V) and 20 (0 V)

Signal unit connection

18 (+24 V) and 19 (0 V)

Alarm stop button

21 and 22

  

VSP-211-L station

The VSP system can also work as a common battery telephone system 

when an external 24 VDC power supply is connected to the system 

amplifier. Two terminals are added for this purpose.

External power in

23 (+24 V) and 24 (0 V)

3.2  Cabling

The recommended cable is 0.5 sq. mm revolved in pairs with an outer 

insulated screen, like RCOP.
The number of wires needed depends on the number of stations in the 

system.

 

● Two twisted pairs are used as microphone (1 pair, terminals 1 & 

2) and speaker (1 pair, terminals 3 & 4) lines. In addition, one wire 

is used for each station selection. A full system with 12 stations 

therefore requires 8 pairs of wires.

 

The screen must be connected to terminal 2 in VSP-211-L to avoid 

noise problems.

Содержание Vingtor Stentofon VSP 12-Way





















Отзывы: