Zenit Powertools BPL-508/2300 Скачать руководство пользователя | Manualshive

Страница: 12 / 14

background image

12

4.

Engine runs un-

evenly.

Incorrect gap in the

spark plug.

Clean, set the correct gap

or replace the plug.

5.

Engine emits lot of

smoke.

Incorrect carburetor

adjustment.

Adjust the carburetor in

the service center.

Inadequate fuel.

Use the correct fuel mix-

ture ratio 25/1.

If it is impossible to define and troubleshoot the problem, contact a specialized

service center.

«
...
10
11
12
13
14
»

Содержание BPL-508/2300















Отзывы:

Нет отзывов

Похожие инструкции для BPL-508/2300

Бренд: Makita Страницы: 36

Бренд: Makita Страницы: 8

Бренд: Makita Страницы: 2

Бренд: Castelgarden Страницы: 404

Бренд: Oleo-Mac Страницы: 32

Бренд: North American Страницы: 16

Бренд: Jonsered Страницы: 36

Бренд: Ruris Страницы: 164

Бренд: Poulan Pro Страницы: 15

Бренд: Poulan Pro Страницы: 16

Бренд: Stihl Страницы: 116

Бренд: Zenoah Страницы: 62

Бренд: Tanaka Страницы: 116

Бренд: Gardol Страницы: 188

Бренд: Oleo-Mac Страницы: 60

Бренд: Echo Страницы: 26

Бренд: AL-KO Страницы: 192

Бренд: Ozito Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды