This tent design is under copyright protection by Flow imports Ltd. The Zempire Logo and related
Campfire mark are registered trademarks of Flow imports Ltd, New Zealand. Any reproduction of this
manual is prohibited without prior consent by Flow imports Ltd.
4x
4.
Connect the C Clips sewn into the
tent around the corresponding pole.
You may need to lay tent down to reach
the top clips.
2.
Insert the end of the pole
without the steel connector
into the 4 way connector
attached to the top of the
tent. Repeat with all 4 poles
1.
Assemble the 2 pole
sections. Ensure that the
poles are inserted fully into
the steel connectors.
5.
Place the vent cover over the top
of the tent and hook on the corners
to the loops sewn along each pole
line. once again, it may be easier to
lay the tent on its side to do this
step.
7.
It is recommended that guy ropes are
pegged out at all times. Try to have guy
ropes at a 45
o
angle to the ground.
3.
Tension the poles and
insert the pins located at the
base of the tent into the
ends.
6.
Ensure the door is closed. Peg out
all peg points around the base of the
tent. Try to make the poles evenly
spaced apart.
This tent design is under copyright protection by Flow imports Ltd. The Zempire Logo and related
Campfire mark are registered trademarks of Flow imports Ltd, New Zealand. Any reproduction of this
manual is prohibited without prior consent by Flow imports Ltd.
4x
4.
Connect the C Clips sewn into the
tent around the corresponding pole.
You may need to lay tent down to reach
the top clips.
2.
Insert the end of the pole
without the steel connector
into the 4 way connector
attached to the top of the
tent. Repeat with all 4 poles
1.
Assemble the 2 pole
sections. Ensure that the
poles are inserted fully into
the steel connectors.
5.
Place the vent cover over the top
of the tent and hook on the corners
to the loops sewn along each pole
line. once again, it may be easier to
lay the tent on its side to do this
step.
7.
It is recommended that guy ropes are
pegged out at all times. Try to have guy
ropes at a 45
o
angle to the ground.
3.
Tension the poles and
insert the pins located at the
base of the tent into the
ends.
6.
Ensure the door is closed. Peg out
all peg points around the base of the
tent. Try to make the poles evenly
spaced apart.
This tent design is under copyright protection by Flow imports Ltd. The Zempire Logo and related
Campfire mark are registered trademarks of Flow imports Ltd, New Zealand. Any reproduction of this
manual is prohibited without prior consent by Flow imports Ltd.
4x
4.
Connect the C Clips sewn into the
tent around the corresponding pole.
You may need to lay tent down to reach
the top clips.
2.
Insert the end of the pole
without the steel connector
into the 4 way connector
attached to the top of the
tent. Repeat with all 4 poles
1.
Assemble the 2 pole
sections. Ensure that the
poles are inserted fully into
the steel connectors.
5.
Place the vent cover over the top
of the tent and hook on the corners
to the loops sewn along each pole
line. once again, it may be easier to
lay the tent on its side to do this
step.
7.
It is recommended that guy ropes are
pegged out at all times. Try to have guy
ropes at a 45
o
angle to the ground.
3.
Tension the poles and
insert the pins located at the
base of the tent into the
ends.
6.
Ensure the door is closed. Peg out
all peg points around the base of the
tent. Try to make the poles evenly
spaced apart.
This tent design is under copyright protection by Flow imports Ltd. The Zempire Logo and related
Campfire mark are registered trademarks of Flow imports Ltd, New Zealand. Any reproduction of this
manual is prohibited without prior consent by Flow imports Ltd.
4x
4.
Connect the C Clips sewn into the
tent around the corresponding pole.
You may need to lay tent down to reach
the top clips.
2.
Insert the end of the pole
without the steel connector
into the 4 way connector
attached to the top of the
tent. Repeat with all 4 poles
1.
Assemble the 2 pole
sections. Ensure that the
poles are inserted fully into
the steel connectors.
5.
Place the vent cover over the top
of the tent and hook on the corners
to the loops sewn along each pole
line. once again, it may be easier to
lay the tent on its side to do this
step.
7.
It is recommended that guy ropes are
pegged out at all times. Try to have guy
ropes at a 45
o
angle to the ground.
3.
Tension the poles and
insert the pins located at the
base of the tent into the
ends.
6.
Ensure the door is closed. Peg out
all peg points around the base of the
tent. Try to make the poles evenly
spaced apart.
This tent design is under copyright protection by Flow imports Ltd. The Zempire Logo and related
Campfire mark are registered trademarks of Flow imports Ltd, New Zealand. Any reproduction of this
manual is prohibited without prior consent by Flow imports Ltd.
4x
4.
Connect the C Clips sewn into the
tent around the corresponding pole.
You may need to lay tent down to reach
the top clips.
2.
Insert the end of the pole
without the steel connector
into the 4 way connector
attached to the top of the
tent. Repeat with all 4 poles
1.
Assemble the 2 pole
sections. Ensure that the
poles are inserted fully into
the steel connectors.
5.
Place the vent cover over the top
of the tent and hook on the corners
to the loops sewn along each pole
line. once again, it may be easier to
lay the tent on its side to do this
step.
7.
It is recommended that guy ropes are
pegged out at all times. Try to have guy
ropes at a 45
o
angle to the ground.
3.
Tension the poles and
insert the pins located at the
base of the tent into the
ends.
6.
Ensure the door is closed. Peg out
all peg points around the base of the
tent. Try to make the poles evenly
spaced apart.
This tent design is under copyright protection by Flow imports Ltd. The Zempire Logo and related
Campfire mark are registered trademarks of Flow imports Ltd, New Zealand. Any reproduction of this
manual is prohibited without prior consent by Flow imports Ltd.
4x
4.
Connect the C Clips sewn into the
tent around the corresponding pole.
You may need to lay tent down to reach
the top clips.
2.
Insert the end of the pole
without the steel connector
into the 4 way connector
attached to the top of the
tent. Repeat with all 4 poles
1.
Assemble the 2 pole
sections. Ensure that the
poles are inserted fully into
the steel connectors.
5.
Place the vent cover over the top
of the tent and hook on the corners
to the loops sewn along each pole
line. once again, it may be easier to
lay the tent on its side to do this
step.
7.
It is recommended that guy ropes are
pegged out at all times. Try to have guy
ropes at a 45
o
angle to the ground.
3.
Tension the poles and
insert the pins located at the
base of the tent into the
ends.
6.
Ensure the door is closed. Peg out
all peg points around the base of the
tent. Try to make the poles evenly
spaced apart.
UV Degradation
Shelter fabrics can be weakened by prolonged
exposure to sunlight. Under normal holiday use,
your ZEMPIRE
®
Shelter will give you many years
of camping enjoyment. However, extended use
in strong sunlight will cause degradation. It is
recommended that during periods of strong
sunlight a ZEMPIRE
®
Roof Cover is used to help
protect from UV damage. UV degradation is not
covered under warranty. The warranty does not
cover permanent sites, displays or commercial
use.
WARNING
KEEP ALL FLAME AND
HEAT SOURCES AWAY
FROM THIS TENT FABRIC
