Zelmer ZVC605AP, Руководство пользователя

Страница: 53 / 56

59
ZVC605-001_v03
25 Outlet filter. The vacuum cleaner is fitted with only one
outlet filter (A or B)
A Anti-bacterial filter Aller-Sweep HEPA H13 (only in
model ZVC605AP, ZVC605AQ)*
B
Anti-aromatic filter HEPA H13 with activated charcoal
(only in model ZVC605CA)*
26 Inlet filter casing*
27 Inlet filter*
28 Parquet brush “BNB” (Brush Natural Bristle)
The parquet brush is used to clean and polish hard,
scratch sensitive surfaces such as wooden floors, floor
panels, parquet, marble, tiles, etc.
Delicate and soft natural bristles ensure maximum
vacuum effectiveness and protects against scratching
the cleaned surface.
29 Switchable combination brush
30 Suction nozzle for mattresses cleaning (only in model
ZVC605AP, ZVC605AQ)
31 Brush for collecting pet hair from carpets (only in model
ZVC605CA)
32 Battery-powered electrobrush (only in model ZVC605AQ)
* – installed in the vacuum cleaner
Get vacuum cleaner ready for operation
1
Insert the curved hose end in the opening of the vacuum
cleaner and gently press. A characteristic click indicates that
the hose has been properly installed.
2 Connect the other end of the hose (handle) with the
telescopic suction tube. In order to do so press the locking
device “A” and slide the tube into the hose handle so that
the locking device “A” is blocked in opening “B” .
3
Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/ pull the tube
together.
4 Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5 Use combination carpet & floor brush for vacuuming both
hard surfaces and carpets. To clean hard surfaces – wooden
floors, plastic floors, ceramic tiles etc. pull out the brush by
pressing the switch on the combination brush according to
the figure . Retract the brush when vacuuming carpets
(set the switch in “ ”).
6 Use the handle to move or lift the vacuum cleaner. Press
handle to release/lock it.
7 Pull the plug and cord out of the vacuum cleaner. Do it
smoothly (do not tug) to avoid cord tangling and blocking in
the vacuum body.
While puling out the cord pay attention to the
yellow stripe which signals the end of the
cord. Further attempts to pull it out may cause
damage.
B
8 Plug in the appliance.
Before operation make sure that the SAFBAG
bag is installed in the vacuum cleaner chamber
and that inlet filter and the HEPA outlet filter is
installed in the appliance.
9 Switch on the vacuum cleaner by pressing the
button .
10 The vacuum cleaner is equipped with an electronic
power control which allows for a gradual suction power
adjustment during vacuuming. Power is adjusted with the
+ / – push buttons, “ + ” to increase the suction power or “ – ”
to reduce the suction power. Setting the suction power is
indicated by lighting of the corresponding number of LEDs.
The following suction power settings are recommended:
– for delicate fabrics such as curtains, etc.
– for upholstered furniture
– for carpets and floor coverings
– vacuuming parquet floor, stone and tiled flooring
– vacuum cleaning heavily soiled surfaces
– “TURBO” mode
“TURBO” mode allows you to set the maximum
suction power with a single button. Once
the
button is pressed, all power level
indicators will go off and the “TURBO” mode
indicator will light up.
To turn off the “TURBO” mode press the “+” or
“–” button. Press the “+” or “–” button to set
the vacuum cleaner to “
”.
The power may also be adjusted individually depending on
the type of surface, vacuum effectiveness and suction power
of the switchable combination brush.
11 The vacuum cleaner is also equipped with a mechanical
suction power regulator located on the suction hose handle.
It may be used to temporarily adjust the suction power with
no need to use the “ + ” and “ – ” buttons.
Filter disassembly
Before changing the filters make sure that the vacuum cleaner
is switched off and unplugged from the mains supply.
HEPA 13 OUTLET FILTER
The vacuum cleaners are equipped with an H13 outlet filter
HEPA (High Efficiency Particulate Air).
1 To replace the HEPA outlet filter, put the vacuum cleaner
in a vertical position.
2 There is a special indent in the outlet and foam filter
cover to open it.
3 Place your hand in the indent and move the cover
towards .
C