Zelmer zvc015zq, Руководство пользователя

Страница: 25 / 28

31
ZVC015ZQ-001_v02
Electrostatics
Vacuuming some surface types in low humidity conditions
may cause the appliance to become charged with static. It is
a natural phenomenon, it does not damage the appliance
and it is not its defect.
In order to minimize this effect, it is recommended to:
●
increase the humidity in the room,
●
use general anti-static agents.
Appliance elements
A
1 ON/OFF button
2 Handle
3 Handle release button
4 Vacuum cleaner housing
5 Electrobrush release button
6 Dust container release button
7 Charging socket
8 Electrobrush
9 Power adapter with power cord
10 Battery charging indicator
11 Dust container (fitted in the vacuum cleaner)
12
Pre-filter (fitted in the dust container)
13 CYCLONE module (fitted in the dust container)
14 EPA E10 Primary filter (fitted in the dust container)
Assembling – preparing the vacuum
cleaner for operation
1 Open the vacuum cleaner handle.
2 Connect the vacuum cleaner housing with the
electrobrush.
●
Before starting, make sure that EPA E10 filter and pre-
filter are installed in the dust container.
3 Press on/off to start vacuuming.
Vacuum cleaner accessories
ELECTROBRUSH 8
Electrobrush is used to clean short hair carpets, carpet
floorings, floors or tiles. With the rotary brush it has the ability
to remove old and stubborn dirt, and difficult-to-remove dirt
such as threads, rags, paper, etc.
It is practically useful in households with pets, where removing
the animal hair from the carpets and floorings is very onerous.
Do not use the electrobrush on long hair
carpets. When used on this type of carpet for
a longer time, protection will activate and the
electrobrush will switch off automatically. This
is normal feature and protects the electrobrush
from damage. To switch on the device again,
wait for a few minutes.
B
If the electrobrush comes in contact e.g. with
a hand, protection feature will automatically
switch off the brush in order to avoid injury.
Battery charging
C
Before charging, make sure the appliance is switched off.
1 Charge the appliance when the charging indicator
flashes red.
2 Place the vacuum cleaner near a wall outlet.
3 Plug the power cord into the appliance and then connect
it to the wall outlet.
4
When charging, the battery charging indicator lights turns
green in sequence to indicate that charging is in progress.
5 Battery charging cycle takes about 5 hours. The top
charging indicator will then light up continuously.
It is recommended to continue charging for another 1-2 hours.
6 Disconnect the appliance when battery is fully charged.
●
When batteries are fully charged the vacuum cleaner will
operate for 19 minutes maximum.
During three initial charging cycles the
batteries should be fully discharged, and the
charging time should be at least 12 hours in
order to obtain the maximum battery charge.
Subsequent charging can be carried out in the
manner described above.
When voltage drops down, the vacuum cleaner
will automatically switch off, therefore it is
recommended to keep it fully charged before use.
End of operation, cleaning and maintenance
CLEAN THE DUST CONTAINER AND THE CYCLONE
MODULE
1 Press the dust container release button and tilt it away
from the vacuum cleaner.
2
Remove the CYCLONE module from the dust container.
In order to do this, grasp the CYCLONE module and pull it
from the container.
3 Empty the dust container.
4 Rinse the Interior of the dust container with lukewarm
water, and then wipe dry with a cloth.
Clean the dust container after each use.
5 Remove the EPA E10 filter from the CYCLONE module.
6 Remove the pre-filter from the EPA E10 filter.
If both EPA E10 primary filter and pre-filter are
dirty, you can replace them, clean them or rinse
under running water. Filters must dry naturally.
Do not dry the filters using a hair dryer or place
them on the radiators or heating elements.
D