Zelmer sb1000, Руководство пользователя

Страница: 45 / 46

49
SB1000-001_v01
Cleaning and maintenance
Clean the appliance immediately after use to
prevent the deposits inside the blender jug.
Pour approx. 750 ml of water into the blender jug
●
(5) and
start the appliance for about 10 seconds by pressing and
holding the “TURBO” button.
Remove the water from the blender jug
●
(5) , turn it upside
down and allow it to dry.
Wash the jug
●
(5) , lid (7) , stopper (9) and blade unit (10)
in warm water with washing-up liquid, if necessary.
Rinse it under the stream of clean, running water, and
●
dry it.
If you left the pitcher for a long time without cleaning and
●
the pieces of mixed ingredients stuck to the inside of the
pitcher, use a nylon brush.
Do not wash the blender jug
●
(5) , lid (7) , stopper (9) ,
coffee grinder (12) or blade unit (10) in a dishwasher.
Aggressive cleaning agents may damage the surface of
the accessories.
Wipe the motor unit
●
(1) casing with a soft, damp cloth.
Never immerse the motor unit (1) in water or
any other liquid.
Do not clean the motor unit casing
●
(1) with aggressive
detergents, such as emulsion, milk, paste, etc. They can
remove the graphic symbols.
Never clean the glass blender jug
●
(5) and the grinder
container (13) with coarse sponges.
Dry all elements of the appliance thoroughly after washing.
●
BLADE UNIT ASSEMBLY
1 Place the sealing ring (11) onto the blade unit flange (10) .
2 Remove the lid (7) from the blender jug (5) , pulling the
locked stopper with level indication (9) .
3 Turn the blender jug (5) “upside down”, and put it on
a stable, level surface.
4
Insert the blade unit (10) into the opening at the bottom
of the blender jug (5) .
5 Hold the blender jug (5) with one hand, and turn the
blade unit anticlockwise with the other hand, until you feel
the resistance.
The twisting direction is shown at the bottom
of the blade unit.
BLADE UNIT DISASSEMBLY
1 Unplug the appliance from the mains socket.
2 Remove the lid (7) from the blender jug (5) pulling the
locked stopper with level indication (9) .
3 Remove the content of the blender jug (5) .
4
Clean the blender jug (see “Cleaning and Maintenance”).
Turn the blender jug (5) upside down, and put it on a stable,
level surface.
D
E
Before chopping, remove the veins, membranes
and fat from the meat, and then chop it into
pieces of approx. 2x2 cm in size.
1 Put the ingredients into the grinder container.
Do not exceed the maximum content level
indicated on the grinder container.
2 Put the grinder base (15) with blade unit into the grinder
container (13) . Make sure that the grinder base sealing ring
is fixed tightly to the narrowing in the grinder container.
3 Grab the clutch cover, and turn the grinder base with
blade unit anticlockwise, until you feel the resistance.
The twisting direction is shown at the bottom
of the grinder base with blade unit.
4 Turn the grinder upside down, and mount it onto the
motor unit (1) , so that one of the protruding elements in the
grinder lid fits in the cut-out in the motor unit.
5 Turn the grinder (12) clockwise to lock it in place, until you
feel the resistance. The control panel illumination will go on.
6 Run the appliance.
We recommend you to use the “TURBO”
programme or set the appliance at the
maximum speed.
Set the lowest speed to obtained the best
results of grinding nuts.
Use the mill to grind one type of product only.
Grinding of various products immediately one
after another without careful washing may
result in diffusion of odour and/or flavour from
one product to another one.
The grinder should not be running continuously
for more than 30 seconds. Switch the appliance
off after 30 seconds, and wait another 30
seconds before you run it again.
7 When the grinding has been finished, switch the
appliance off pressing the ON/OFF button . Unplug the
appliance from the mains socket.
8
Turn the grinder anticlockwise so that the protruding
element in the grinder lid fits in the cut-out in the motor unit.
9 Remove the grinder from the motor unit.
Open the grinder, following the instructions set forth in
●
section
3
, but in a reverse order.
Always wash the grinder container and the base
with blade unit in warm water with washing-up
liquid immediately after use. Wipe the grinder
sealing ring with a damp cloth.