![background image](http://html1.mh-extra.com/html/zelmer/je1000/je1000_user-manual_3403234047.webp)
49
JE1000-001_v01
Technical data
The technical data are given on the name plate.
Maximum continuous operation time:
10 minutes
Time interval between successive uses:
15 minutes
Noise level (L
WA
)
80 dB/A
The juice extractor type JE1000 does not require connection
to a grounded socket
.
ZELMER appliances satisfy the requirements of relevant
standards.
The appliance meets the requirements of the following
directives:
Low Voltage Device (LVD) – 2006/95/EC;
–
Electro-Magnetic Compatibility (EMC) – 2004/108/EC.
–
The product is marked with CE symbol on the name plate.
Construction of the appliance
(Fig. A)
1
Motor unit
2
Suction cups
3
Power cord
4
Power on/off button, level 1 – level 2
5
Locking clamps
6
Fasteners
7
Skimmer
8
Juice bowl
9
Spout
10
Pulp container
11
Strainer
12
Lid
13
Pusher
14
Jug
15
Froth separator
16
Brush
Preparing for operation (disassembling) (Fig. B)
Before first use, disassemble the appliance,
wash and dry all attachments in contact with
the processed fruit or vegetables.
1
Place the appliance on a clean hard, and dry surface
near a wall socket.
2
Hold the locking clamps
(5)
from below on both sides
and pull away from the motor unit.
3
Lift locking clamps
(5)
to release the lid
(12)
and lower
when released.
4
Remove the pulp container
(10)
and the pusher
(13)
.
Remove the lid
(12)
and the juice bowl
(8)
together with the
strainer
(11)
.
Wash all parts (except the motor unit) carefully
in hot water with wash-up liquid. You can
also clean them in a dishwasher at max. 60°C
(except the strainer and the motor unit). Once
clean, replace the parts after drying them first
thoroughly.
Assembling the appliance
(Fig. C)
1
Place the juice bowl
(8)
on the motor unit
(1)
, inserting
the spout
(9)
in the opening of the motor unit casing.
2
Mount the strainer
(11)
on the skimmer
(7)
, press it all the
way in, and check if it is well mounted and swivels easily.
3
Place the lid
(12)
on the juice bowl
(8)
.
4
Lift up both clamps
(5)
and fix them on to the fasteners
(6)
located on the lid.
5
Press the clamps
(5)
to the motor unit
(1)
(you will hear
a characteristic click).
6
To mount the pulp container
(10)
under the lid
(12)
,
proceed as follows: lean the pulp container
(10)
and place
it under the juice bowl
(8)
. Then slide it in towards the motor
unit
(1)
. Place the Jug
(14)
under the spout
(9)
.
If you fail to assemble any of the parts (e.g. the
juice bowl, lid, pulp container or locking
clamps) or do it improperly, a safety device will
prevent the switch-on of the appliance.
Starting and operating the juice
extractor
(Fig. D)
Make sure that the power on/off button is set to
●
“0”
.
Unwind a sufficient length of the cord. The remaining
●
cord can be stored inside the drive housing. Slip the
remaining cord through an opening located at the side
of the appliance.
1
Insert the power cord
(3)
plug into the socket and
press the on/off button
(4)
to start the appliance, selecting
speed level 1 (position I – low rotation speed for soft fruit
and vegetables such as raspberries, tomatoes, cucumbers,
Tip
Product information and tips for use
Thoroughly clean all parts of your appliance before the
●
first use.
The appliance is intended for domestic use. In case
●
it is used for food business purposes, the warranty
conditions shall change.