62
Disconnect the telescopic tube from the hose and the
●
nozzle or brush.
In case of vacuuming or picking up water with the use
●
of the water
fi
lter module, remove the dirty water from
the tank.
It is recommended to wash the container,
fi
lters
●
(disassembly below) and partition thoroughly after each
use – changing water several times.
ATTENTION! If you do not clean the above-mentioned
parts or clean them insuf
fi
ciently it may lead to the loss
of the
fi
ltration capabilities of the inserts and foam and
cause the formation of bacteria and mites.
Dry all the cleaned parts thoroughly before reassembly.
Filter disassembly
FOAM FILTER I
1
Open the lid of the
fi
lter unit – press the handle and lift
the lid.
2
Take out the
fi
lter, wash it under running water, dry and
reinsert.
Close the
fi
lter unit lid by pressing it until you hear
●
a characteristic click.
FOAM FILTER II
It is recommended to wear rubber protective gloves while
dismantling the
fi
lter.
1
Grab the foam
fi
lter with your
fi
ngers and remove it from
the
fi
lter unit body.
2
Wash under running water, dry and reinsert.
ATTENTION! Do not hand wash the
fi
lter foam, do not
wring it, do not wash it in washing machines. Avoid
crumpling, stretching and deforming. After cleaning
dry the foam in room temperature. Never dry the foam
on heaters, stoves, etc.
INLET FILTER
1
Press the “PRESS” button and remove the tank lid.
2
Remove the SAFBAG
(25)
dust bag module from the
container.
3
Take out the SAFBAG dust bag from the module (see
chapter TRADITIONAL CLEANING WITH SAFBAG DUST
BAG – disassembly/assembly of the SAFBAG dust bag).
4
Release the fastening hook which
fi
xes the lid of the
SAFBAG dust bag module with the basket and pull the
basket aside.
5
Take out the
fi
lter, wash it under running water, dry and
reinsert.
6
Close the basket of the SAFBAG dust bag module by
pressing it until you hear a characteristic click.
7
Insert SAFBAG dust bag (see chapter TRADITIONAL
CLEANING WITH SAFBAG DUST BAG – disassembly/
assembly of the SAFBAG dust bag).
8
Insert the dry
fi
ltration module with the SAFBAG
(25)
dust bag into the tank.
Insert and snap the tank lid shut.
●
MOTOR FILTER
A
fi
ltration fabric is inserted in the motor cooling cycle which
is to catch the coal dust which arises due to the natural wear
and tear of the brushes and the commutator in the motor.
1
Remove the tank from the vacuum cleaner.
2
Place the vacuum cleaner with the “wheels upwards” so
that the upper sloping surface and the handle are rested on
the
fl
oor. Insert a
fl
at, narrow tool e.g. a screwdriver into the
special slot of the
fi
lter lid; pry the fastening with an upward
hand movement (lever principle) which will release the lid
latch while being bent.
3
If the motor
fi
lter
(8)
is dirty, it is possible to rinse the
fi
lter
(8)
under running water. Remember to dry the above
mentioned
fi
lter before reassembly.
4
Insert the new/rinsed motor
fi
lter
(8)
, make sure that the
fi
lter edges do not remain outside the outline of the section.
Snap the
fi
lter lid shut by
fi
rst inserting the lower fastening
and then pressing the fastening so that the upper fastening
clicks into place at the edge of the appliance body.
OUTLET HEPA FILTER AND FOAM FILTER III
The HEPA outlet
fi
lter should be replaced after about 30
hours of operation (6 months) or earlier in case of heavy dirt.
1
Remove the tank from the vacuum cleaner.
2
Place the vacuum cleaner with the “wheels upwards” so
that the upper sloping surface and the handle are rested on
the
fl
oor.
3
Slide the slider of the
fi
lter cover interlock to the “open”
position and remove the
fi
lter lid.
4
Remove the foam
fi
lter III
(11)
. Rinse or replace if the
fi
lter becomes dirty. Remember to dry the
fi
lter before
reassembly.
5
Remove the foam
fi
lter III
(11)
and next remove the HEPA
fi
lter by grabbing the handle. Replace with a new one if the
fi
lter becomes dirty.
It is recommended to periodically inspect the condition of the
fi
lter, especially if there was a water over
fl
ow to the outside of
the vacuum cleaner. In case of detecting damage (a break)
in the
fi
lter layer or if the layer is evenly covered with dust,
the
fi
lter should be replace with a new one.
6
If the HEPA
fi
lter is dirty, replace it with a new one or
rinse under running water. Remember to dry the
fi
lter before
reassembly.
7
Reinsert the
fi
lters, insert the
fi
lter lid and press
fi
rmly.
8
Slide the slider of the
fi
lter cover interlock to the “closed”
position.
Turn the vacuum cleaner to its natural position (on four
wheels).
F
G
H
I
J
Содержание Aquos 829
