![background image](http://html1.mh-extra.com/html/zelmer/28z024/28z024_instructions-for-use-manual_3355574062.webp)
62
After operation press and hold
–
button for about 2 sec
-
onds to switch off the iron. You can hear single sound signal. Then the
display (4)
goes off.
Disconnect the iron from mains supply outlet.
–
When the iron gets cool completely, store it vertically in a safe place.
–
It may be necessary to press the burst of steam button a few times to
start this function.
For optimum steam quality, do not operate the Burst of Steam more
than three times after the control light goes off.
When the control light (6) glows do not operate the Burst of Steam
more than 3 times in one cycle.
Burst of steam in vertical position
– Always follow the garment
manufacturer’s ironing instructions mentioned at the garment label.
This function provides extra amount of steam to remove wrinkles on delicate
garments in hanging position, hanging curtains, or other hanging fabrics.
Warning:
Do not apply steam on any clothes or fabrics that are being worn by
human or pets. Never direct the steam to human or pets.
Fill the water tank in as described under
–
“How To Fill Water “
.
Connect the iron to a suitable mains supply outlet.
–
The
–
display (4)
glows for a moment and you can hear single sound sig
-
nal. Then the
display (4)
go off.
Set the temperature
–
(5 level)
or higher with
or
buttons, as described in
“Temperature
Setting”
item.
The steam ironing indicator
–
(4)
ap
-
pears on display.
The appliance is ready for operation.
–
Hold the iron between 15 and 30 centime
-
–
tres away from the garment.
Press the
–
Burst of Steam Button
(3)
once – steam will shoot from
the holes of the soleplate. The steam penetrates the fabric removing
wrinkles.
For stubborn wrinkles, wait a few seconds before pressing the
–
Burst
of Steam Button (3)
again. Most wrinkles can be removed within three
presses.
After operation press and hold
–
button for about 2 sec
-
onds to switch off the iron. You can hear single sound signal. Then the
display (4)
goes off.
Disconnect the iron from mains supply outlet.
–
When the iron gets cool completely, store it vertically in a safe place.
–
It may be necessary to press the burst of steam button a few times to
start this function.
For optimum steam quality, do not operate the Burst of Steam more
than three times in one cycle.
Build-in Anti-scale System
The build-in anti-scale cartridge is designed to reduce the build-up of lime
scale which occurs during steam ironing. This will prolong the working life
of your iron.
Attention: Please note that the anti-scale cartridge will not completely
stop the natural process of lime scale build-up.
Self-cleaning
This function removes the scales and minerals built up in the Steam Cham
-
ber. The iron will remain in the best condition if this function is performed
at least once a month or more regularly (usually after more than 8 hours of
operation) depending on the hardness of the water used. You can see
on
LCD display (4)
.
Fill the water tank in as described under
–
“How To Fill Water”
.
Place the iron on the surface in vertical, resting position.
–
Connect the iron to a suitable mains supply outlet.
–
The
–
display (4)
glows for a moment and you can hear single sound sig
-
nal. Then the
display (4)
go off.
Set the temperature
–
(9 - highest level) with
or
buttons, as described in
“Temperature Setting”
item.
Press and hold
–
button for about 2 seconds to switch off
the iron. You can hear single sound signal. Then the
display (4)
goes off.
Disconnect the iron from mains supply outlet.
–