Zell AC1800 Скачать руководство пользователя страница 3

Страница: 3 / 63

1 About this operation manual

This operation manual describes the ZELL Air-Con Service Station

This manual is for those who have the required professional ability of

providing the maintenance service on vehicle air conditioning system.

This manual contains all the instructions necessary for safe and effective

operating of the air Conditioning service Station. Read this operation manual

carefully before putting the device into using for the first time.

Also note the following:

■ the operator should comply with the laws about the service of vehicle air-

conditioning by local government.

■ the operator should be familiar with basic technical information of vehicle

air- conditioning

■ Instructions from the refrigerant manufacturer

■ Instructions from the car manufacturer

■Any special instructions on servicing vehicle air conditioning systems which

applied at your company

Keep this operation manual in the tool box of Air-Con Service Station, so that

any information needed is always at your hand.

Содержание AC1800
































































Результаты поиска

Содержание AC1800

Отзывы:

Похожие инструкции для AC1800

Бренды по названию

Популярные бренды

Zell AC1800, Руководство по эксплуатации

Результаты поиска

Содержание AC1800

Отзывы:

Похожие инструкции для AC1800

Бренды по названию

Популярные бренды