ZComax XN-2050 Скачать руководство пользователя страница 62

Страница: 62 / 71

Chapter 5 Management Page 54

Please make sure that you have downloaded the latest and correct firmware from the product

support website and store it in local drive before upgrading the firmware of the IEEE 802.11n (Draft

2.0) 2.4GHz Wireless Broadband Router.

To upgrade the latest firmware, complete the following:

Using browser to access (http://192.168.1.254) AP’s main page.

1. Select

Upgrade Firmware

from the Management section.

2. Input the exact file path and name by clicking

Browse

button, then press

Upload

button to

upgrade the firmware.

3. Please wait for 80 seconds.

If download fail, please repeat the step 1~3 to download again.

Do not power off the unit when it is being upgraded.

Save/Load Setting

This page allows you to save current settings to a file or restore from a file.

Figure 51 Save/Reload Settings

Save Settings to File:

Allow back up your current configuration to your computer.

Load Settings from File:

Restore your configuration from a previously saved configuration file.

Reset Settings to Defaults:

The reset button will clear all user-entered configurations and will reset the device settings

back to its factory default value.

-LAN IP address: 192.168.1.254

Warning:

Содержание XN-2050








































































Результаты поиска

Содержание XN-2050

Отзывы:

Похожие инструкции для XN-2050

Бренды по названию

Популярные бренды

ZComax XN-2050, Руководство пользователя

Результаты поиска

Содержание XN-2050

Отзывы:

Похожие инструкции для XN-2050

Бренды по названию

Популярные бренды