background image

Zaxcom ZMT4                                                                                                                         Specifications 

 

 

30 

Specifications 

Transmitter 

RF Modulation: Proprietary Digital Method 

ZMT3-Phantom .5 RF Frequency Range: 512 - 608 MHz 

ZMT3-Phantom .6 RF Frequency Range: 576 - 698 MHz 

RF Frequency Step: 100 KHz 

RF Bandwidth in ZHD48 Mode: 50 KHz 

RF Bandwidth in ZHD96 Mode: 100 KHz  

RF Bandwidth in XR Mode: 200 KHz 

Channel Separation in ZHD48 Mode: as close as 100 KHz (receiver dependent) 

Channel Separation in ZHD96 Mode: as close as 200 KHz 

Channel Separation in XR Mode: 400 KHz  

Antenna Connector: 50 Ω SSMA Female

 

Emission Designator: 180 KV2E, 100 KV2E, 50 KV2E 

FCC Part: 74.861 

Audio 

Dynamic Range: 136 dB 

Distortion: 0.01% 

Frequency Response: Mode 0: 20 Hz to 16 kHz / T & M Mode 0.2 Hz to 16 kHz 

High Pass Filter: Off or 30 to 220 Hz, Steps: 10(6dB Per Octave) 

Unbalanced Lavaliere Mic Power: 5.0v @ 10mA max 

Balanced Mic Power: 12v @ 25mA max 

Balanced Mic Power: 24v @ 10mA max 

Balanced Mic Power: 36v @ 10mA max 

Balanced Mic Power: 45v @ 10mA max 

Mic Connector: 3-Pin Micro LEMO 

Mic Configuration: Balanced (3-wire) / Unbalanced (2-wire) 

Input Range: -60 to -30 dBu 

Mic Impedance: 3.4 k Ω (680 Ω with 12v power mode)

 

ADC Bit-Depth: 32 Bits 

ADC Sampling-Rate: 32 kHz 

Time code Reader/Generator 

Timecode output: 3-Pin Micro LEMO 

Clock Accuracy: 1.54 PPM (1 Frame Out in 6 Hours) 

Timecode Type: SMPTE 

Timecode Frame-Rates: 23.98, 24, 25, 29.97NDF, 29.97DF, 30NDF, 30DF 

Recording 

Media: Micro SD Card (Flash Memory) 

File Format: .ZAX convertible to BWAV, MP3 

2.4 GHz ZaxNet Receiver 

RF Frequency Range: 2.403 to 2.475 GHz 

RF Modulation: Digital Spread Spectrum 

RF Frequency Step: 0.001 GHz (1 MHz) 

RF Bandwidth: 1 MHz 

Channel Separation: 2 MHz 

Sensitivity: -96 dBm 

Physical 

Weight: 2.2 ounces (62.3 grams) with battery 

Dimensions (H x W x D):  2.2 X 1.6 X .55 inches (55 X 40.6 X 14 mm) 

Display: Graphic OLED 

Power

 

Power Output: 10 / 50 mW – Software Selectable 

Power Consumption: 125 mA @ 4.2v (525W) with 50mW TX (no ZaxNet or Phantom pwr) 

Battery Type: NP-50 

Lavalier Battery Life: Up to 6.5 hours 

Phantom Power Battery Life: Up to 5 hours 

All Specifications are subject to change without notice.

 

Содержание ZMT4


































Отзывы: