13
12. How to change an option or
a programme during its cycle
Before you make any change, you must pause the
machine by pressing the “
Start/Pause
” button.
It is possible to change the temperature or any option
before the programme carries it out.
Changing a running programme is possible only by
cancelling it and selecting a new programme.
The machine will resume the cycle
from the beginning
and the washing water in the tub will not emptied out.
If it is necessary to drain the water, proceed as follows:
• PAUSE the machine by pressing the “
Start/Pause
”
button;
• press the “
Skip/Reset
” button repeatedly, until only
the “
Drain
” light remains lit;
• press the “
Start/Pause
” button again.
When the water has been drained, the display shows a
blinking zero. You may now select a new programme
and press the “
Start/Pause
” button to start it.
13. How to cancel a programme
during its cycle
To cancel a programme that is being carried out, first
pause the washing machine by pressing the
“
Start/Pause
” button, then press the “
Skip/Reset
”
button repeatedly, until the display shows
three flashing
dashes.
14. How to open the door during
the cycle of a programme
You can open the door, after having set the washing
machine to Pause, provided the following conditions
exist:
• the washing machine is not in the heating phase
beyond 55°C;
• the level of the water is not high;
• the drum is not turning.
If these requirements are met, when you pause the
washing machine, the door can be opened.
Should it not be possible to open the door, and should it
be absolutely necessary to do so, switch the machine off
by pressing the “
On/Off
” button.
After approximately 3 minutes, you can open the door.
Pay attention to the level and temperature of the
water in the washing machine!
When you close the door and press the “
On/Off
” button
again, the washing machine will resume the programme
from the point where it had been interrupted.
15. End of programme
At the end of the programme, the washing machine
stops automatically, gives an audible signal, the
“
Start/Pause
” button light goes off, and the display
shows a blinking zero.
If you had selected the “
Rinse Hold”
option, the door is
locked, the Start/Pause button light goes off, the pilot
light of Rinse Hold remains lit to indicate that the water
must be drained. The display shows a flashing zero.
To complete the cycle, press “
Skip Reset
” button
once
,
all the leds are off, the display will show three flashing
dashes, then choose one of the following options:
•
Drain only:
select any washing programme by means
of the
FABRIC
button (3) and press repeatedly the
“
Skip Reset
” button until the only led “
Drain
” on the
programme progress display illuminates. Depress
“
Start/Pause” button
• Drain and Spin:
press
FABRIC
button in order to
select the desired programme and press the “
Skip
Reset
” button until the only led “
Spin
” on the
programme progress display illuminates.
You can change the spin speed by means of “
Spin
”
button if needed, then depress “
Start/Pause” button
.
When the programme has been completed, a blinking
zero appears on the display and the audible signal is
given.
Press the Skip Reset button repeatedly to erase the
programme that has just been carried out. If you
omit to do this, the next time you switch the washing
machine on, the flashing zero will appear on the
display and you will hear the audible signal.
Note
: when you switch the machine on, if you must
erase the previously performed programme, it is also
sufficient to press the FABRIC button and select a new
programme.
Press the “
On/Off
” button to switch the machine off.
The relevant light will go out.
Remove the laundry from the washing machine.
Check whether the drum is completely empty, by
rotating it with your hand. The purpose of this is to
prevent any items of laundry from remaining
accidentally in the drum, where they might get damaged
in a subsequent wash (e.g. by shrinking) or bleed colour
into another load of laundry. We advise you to close the
water supply tap and disconnect the plug from the
socket. Leave the door ajar in order to air the washing
machine.
