Zanussi ZWACR0723V, Руководство пользователя

Страница: 16 / 36

16
Step 6: Install the unit into the cabinet
Step 7: Install the frame
1. Slide the unit into the cabinet until it is firmly against the rear of the cabinet. Care is required to ensure the foam sealing strips on
the cabinet remain in position (See Fig.8).
2. Connect the air conditioner to the power and position excess cord length beneath the air conditioner base.
3. Engage the chassis fixing brackets into the bottom cabinet rail and secure to the base with the screw provided.
1. Hook the upper edge of the frame. Then connect the coupler
plugs and make sure not to interfere with the temperature sensor
cable(see Fig.9).
2. Press the both side and lower edge of the frame, and secure it
with the two screws at the bottom of the frame
.
( See Fig. 10)
Model C:
1. Remove four screws located on both sides and the back of the
cabinet as shown in Fig.5C.
2. Grasp the handle on the chassis and carefully slide the air cond-
itioner out of the cabinet.(see Fig.6)
Step 5: Install the cabinet
NOTE:
Unit may be supported by a solid frame from below or by
a hanger from a solid overhead support(not suppied, purchase
separately, please contact the dealer).
1. When need to drain off water, install the drain plug on the ch-
assis board.
2. Prepare the hole in the wall so that the bottom of the cabinet
is well supported, the top has minimum clearance and the air
inlet louvers have clearance as shown in previous page(Fig.
Option A & B). Holes from the outside through to the cavity
should be sealed. The cabinet should slop down towards the
rear by about 5~7mm to allow water formed during operation
to drain.
3. Install the cabinet into the wall and secure. Ensure the foam
seals are not damaged. Flash, seal or fill gaps around the inside
and outside to provide satisfactory appearance and protection
against the weather, insects and rodents. (see Fig.7)
Flash or seal around
external wall frame
or architrave
Drain pan
Preferred method of installation into a
timber framed wall, partition or window
Sturdy timber
frame all
round unit
Timber framed
wall or partition
External support
frame at balance
point of air conditioner
Alternatively, brackets as
illustrated below may be used
Flash or seal around
external wall frame
or architrave
Drain pan
Alternative method of installation if
external support can not be provided
Sturdy timber
frame
Timber framed
wall or partition
Ensure louvers
are entirely
outside the wall
Steadying bracket
(one per side)
Solid timber support
Fig.5B-ModelB
Fig.5C-ModelC
Fig.6
Fig.7
WALL
CABINET
SCREWS
Fig.5D-ModelD
Fig.8
Fig.9
Model B:
1. Remove one screw securing the chassis fixing bracket, then take
down the chassis fixing bracket. Remove two screws located on
the back of the cabinet as shown in Fig.5B.
2. Grasp the handle on the chassis and carefully slide the air cond-
itioner out of the cabinet.(see Fig.6)
Model D:
1. Remove one screw securing the chassis fixing bracket, then take
down the chassis fixing bracket.(see Fig.5D)
2. Remove four screws located on both sides and the back of the
cabinet as shown in Fig.5D.
3. Grasp the handle on the chassis and carefully slide the air cond-
itioner out of the cabinet.(see Fig.6)
Step 8: Install the air filter and front panel
1. Insert the air filter into the frame’s slot from upside to underside.
(See Fig. 2)
2. Hang the front panel on the frame’s buckle, then press the front
panel into the frame’s slot until you hear a click (see Fig.11).
3. Switch unit on. Check for operation of the unit and check for
vibration after installation.
4. Fit the drain pan to the cabinet and run a drain hose to a suitable
location if required.
Fig.10 Fig.11