background image

13

 

Fitting the Wall Brackets

•  Draw a vertical line on the supporting wall up to the 

ceiling, or as high as practical, at the centre of the area 
in which the hood will be installed.

•  Draw a horizontal line at 650 mm above the hob for 

installation without the back panel, or at height H 
(H=height of the visible part of the panel) for instal-
lation with the back panel.

• Place bracket 

7.2.1

 on the wall as shown about 1-2 

mm from the ceiling or upper limit aligning the centre 
(notch) with the vertical reference line.

•  Mark the wall at the centres of the holes in the 

bracket.

•  Place bracket 

7.2.1

 on the wall as shown at X mm 

below the fi rst bracket (X = height of the upper chimney 
section supplied), aligning the centre (notch) with the 
vertical line.

•  Mark the wall at the centres of the holes in the 

bracket.

•  Place bracket 

7.1

 as shown 95 mm from the verti-

cal reference line and 210 mm above the horizontal 
reference line.

•  Mark the centres of the holes in the bracket.
•  Repeat this operation on the other side.

REAR PANEL (OPTIONAL)

The Rear Panel must be fi tted before fi xing the hood body 
and, if it is to be fi xed at both top and bottom, must be 
fi tted at the correct height prior to installing the bases. 
As this operation is rather complex, it should be carried 
out either by the kitchen installer or a qualifi ed person 
who knows the fi nal dimensions of the units.
For fi xing at the top only, proceed as follows:
•  Rest the back panel on the base, inserting the lower 

plate between the upper surface and the wall, centring 
it on the vertical reference line.

•  Mark the centres of the two holes in the upper plate.

•  Drill ø 8 mm holes at all the centre points marked.
•  Insert the wall plugs (not supplied) in the holes.
•  Fix the brackets using the screws (not supplied).
•   Fix the back panel (where present) using the screws 

(not supplied).

Note:  If the hood is to be installed onto a hollow con-
struction or plaster or partition board wall then special 
fi xing screws will be required (not supplied).

 

Fitting the Canopy Hood

•  Screw the two screws 

item 12d

 supplied onto the 

brackets 

7.1

.

•  Hook the hood body onto the bracket 

7.1

, centring 

it around the vertical line.

•  Use the adjusting screws 

item 12d

 underneath the 

hood to level the hood body

H

X

1÷2

650 min.

7.2.1

7.1

95

95

210

7.1

12.d

INSTALLING THE COOKER HOOD

Содержание ZHC 605

















Отзывы: