Zanussi ZGL62I Скачать руководство пользователя страница 8

Operation

Ignition of the burner

Warning! Be very careful when you use open fire in

kitchen environment. Manufacturer decline any

responsibility in case misuse of the flame

Always light the burner before you put cookware.

To light the burner:
1. Turn the control knob counterclockwise to the maxi-

mum position (     ) and push it down.

2. Adjust the flame after it is regular.

If after some tries the burner does not light, check if

the crown and its cap are in correct positions.

1

2

3

1

Burner cap

2

Burner crown

3

Ignition candle

Warning! If the burner does not light after 15

seconds, release the control knob, turn it into off

position and try to light the burner again after minimum 1

minute.
Important! In the absence of electricity you can ignite the

burner without electrical device; in this case approach the

burner with a flame, push the relevant knob down and turn

it counter-clockwise to maximum gas release position.

If the burner accidentally goes out, turn the control

knob to the off position and try to light the burner

again after minimum 1 minute.

The spark generator can start automatically when

you switch on the mains, after installation or a pow-

er cut. It is normal.

Turning the burner off

To put the flame out, turn the knob to the symbol   .

Warning! Always turn the flame down or switch it off

before you remove the pans of the burner.

Helpful hints and tips

Energy savings

• If possible, always put the lids on the pans.
• When the liquid starts to boil, turn down the flame to

barely simmer the liquid.

Warning! Use pots and pans with bottom applicable

to the dimension of burner.

Do not use cooking vessels on the hotplate that overlap its

edges.

Burner

Diameters of cookware

Rapid

180 - 260 mm

Semi-rapid

120 - 220 mm

Auxiliary

80 - 160 mm

Warning! Pots must not enter the control zone.

Warning! Make sure pot handles do not protrude

over the front edge of the cooktop and that pots are

centrally positioned on the rings in order to achieve

maximum stability and to obtain lower gas consumption.
Do not place unstable or deformed pots on the rings to

prevent from spill and injury.

Warning! Flame diffuser are not recommended.

Information on acrylamides

Important! According to the newest scientific knowledge, if

you brown food (specially the one which contains starch),

acrylamides can pose a health risk. Thus, we recommend

that you cook at the lowest temperatures and do not brown

food too much.

8

 

Содержание ZGL62I













Отзывы: