background image

OPERATION P-257/2

After pressing the push-button the remote control sends a signal on 868,32 MHz 

which controls EXTA FREE receivers. 

Device programming procedure (adding a 

transmitter to the transmitter’s memory) is described in manual instruction of 

particular EXTA FREE system receivers.

 

The range (up to 250 m depending on a receiver) can be changed by means of a 

retransmitter or few RTN-01 retransmitters.

BATTERY CHANGE

Battery discharge status is signalled by several LED red diode flashes during 

transmission time.

  Remove the screws from the bottom part of the remote control.

  Remove the upper cover with the silicon keyboard.

  Remove the battery from the latch.

OPERATION, MOUNTING ROP-01

CONNECTION

  Disconnect power supply by the phase fuse, the circuit-breaker or the switch-dis-

connector combined to the proper circuit.

  Check if there is no voltage on connection cables by means of a special meas-

ure equipment.

  Connect the cables with the terminals in accordance with the installing diagram.

  Install ROP-01 device in installation cable box.

  Switch on the power supply from the mains.

The device can operate in five modes:

MONOSTABLE 

the relay operates only while pressing transmitter’s push-button.

BISTABLE

 (one push-button) the device changes relay status cyclically always after 

pressing the same push-button.

SWITCH ON

 the device switches on after pressing the push-button.

SWITCH OFF 

the device switches off after pressing the push-button.

TIME

 the device switches off according to the adjusted time (tp), but it may be 

switched off before adjusted time finishes. Default settings - 15 seconds.

CAUTION! Adjusted time can not be deleted.

RADIO TRANSMITTERS PROGRAMMING

MONOSTABLE

 mode:

  Press transmitter’s push-button for a longer time.

  Press PROG push-button of ROP-01 device for a longer time until LED red diode 

switches on (constant signal). Next release PROG push-button.

  Release transmitter’s push-button. LED red diode switches on (first signal pul-

sates, next the signal is constant).

  Press the same transmitter’s push-button and release it. LED red diode switches 

on (the signal pulsates) and next it switches off - THE TRANSMITTER IS ADDED.

BISTABLE

 mode:

  Press PROG push-button of ROP-01 device for a longer time until LED red diode 

switches on (constant signal). Next release PROG push-button.

  Press the transmitter’s push-button for a longer time. LED red diode switches on 

(first signal pulsates, next the signal is constant).

  Release transmitter’s push-button. LED red diode switches on (the signal 

pulsates), next the LED red diode switches off - it means the TRANSMITTER IS 

ADDED.

SWITCH ON/SWITCH OFF

 mode (two push-buttons):

  Press PROG push-button of ROP-01 device for a longer time until LED red diode 

switches on (constant signal). Next release PROG push-button.

  Press and release transmitter’s pushbutton. LED red diode switches on (first signal 

pulsates, next the signal is constant).

  Press and release the same transmitter’s push-button. LED red diode switches on 

(the signal pulsates) and next it switches off - THE TRANSMITTER IS ADDED.

TIME

 mode (one push-button)

  Press PROG push-button of ROP-01 device for a longer time till LED red diode 

switches on (constant signal). Next release PROG push-button.

  Press and release transmitter’s pushbutton. LED red diode switches on (the signal 

pulsates, next the signal is constant).

  Press and release the same transmitter’s push-button. LED red diode switches on 

(the signal pulsates) and next it switches off - THE TRANSMITTER IS ADDED.

An exemplary programming procedure with the use of P-257/2 remote controller.

The procedure for the rest of radio EXTA FREE transmitters is analogous. 

CAUTION: 

Every transmitter can cooperate with ROP-01 in a different mode, depending on 

how they were added to the device. One transmitter can be added during one 

programming cycle. Full memory is signalled with pulsating LED red diode.

  Mount a new battery. 

Watch battery polarisation marked on the latch. Wrong 

battery mounting may cause device damage.

  Place back the top cover with the keyboard and tighten the screws.

CAUTION: While changing the battery, it is suggested to press any of the but-

tons for about 5 seconds before putting it into a latch. Next press transmis-

sion button several times to check its operation. If the transmitter does not 

work properly repeat the battery change procedure.

Отзывы: