VER. 003_20.05.2011
COOPERATION AND OPERATING RANGE
Symbol
ROP-01 ROP-02 ROB-01 SRP-02 SRP-03 RWG-01 RWL-01 ROM-01 ROM-10 RDP-01 RTN-01
RNK-02
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
RNK-04
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
P-256/8
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
P-257/4 (2)
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
RNM-10
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
RNP-01
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RNP-02
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RNL-01
160 m
180 m
180 m
lack*
lack*
200 m
160 m
200 m
200 m
160 m
200 m
RTN-01
200 m
200 m
200 m
200 m
200 m
250 m
200 m
250 m
250 m
200 m
250 m
RCR-01
160 m
180 m
180 m
lack*
lack*
200 m
160 m
200 m
200 m
160 m
200 m
RTI-01
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RXM-01
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
* - 1-channel transmitters do not cooperate with roller blind controllers.
CAUTION: The given range concerns open area - an ideal condition without any natural or artificial obstacles. If there are some obstacles between a transmitter and a receiver,
it is advisable to decrease the range according to: wood and plaster: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100%,
glass: from 10 to 20 %, Over- and underground medium and high electrical power lines, radio and television transmitters, GSM transmitters set close to a device system have
also a negative influence on the range.
RADIO TRANSMITTERS PROGRAMMING
ROP-01 OPERATION
ROP-01 can operate in five modes:
MONOSTABLE
the relay operates only
while pressing transmit-
ter’s push-button.
BISTABLE
(one push-button) the
device changes relay
status cyclically always
after pressing the same push-
-button.
SWITCH ON
the device switches on
after pressing the push-
-button.
SWITCH OFF
the device switches off
after pressing the push-
-button.
TIME
the device switches
off according to the
adjusted time (tp),
but it may be switched off before
adjusted time finishes. Default
settings - 15 seconds.
CAUTION! Adjusted time can
not be deleted.
TIME PROGRAMMING
RADIO TRANSMITTERS DELETION
TRANSMITTERS
RECEIVERS
RNK-02
2–channel button
radio transmitter
RNL-01
Radio
foot transmitter
ROP-01
1-channel
radio receiver
RWL-01
Radio lighting
switch
RNK-04
4-channel button
radio transmitter
RTI-01
IR/EXTA FREE
transceiver
ROP-02
2-channel
radio receiver
RWG-01
Remote control
socket
P-256/8
8-channel
remote controller
RNM-10
4-channel radio
modular transmitter
RDP-01
1-channel
radio dimmer
SRP-02
Radio roller blinds
controller
P-257/4
4-channel
remote controller
RNP-01
4-channel
radio transmitter
ROB-01/12-24V
Radio
gate controller
SRP-03
Central radio roller
blinds controller
P-257/2
2-channel
remote controller
RNP-02
4-channel
radio transmitter
ROM-01
1-channel radio
modular receiver
ROM-10
2-channel
radio modular receiver
RCR-01
Radio
motion sensor
RXM-01
Translator
RS-485/EXTA FREE
ACCESSORIES
ANT-01
External antenna
RTN-01
Retransmitter
MONOSTABLE
mode:
BISTABLE
mode:
SWITCH ON/SWITCH OFF
mode (two push-buttons):
TIME
mode (one push-button):
An exemplary programming procedure with the use of P-257/2 remote controller. The procedure for the rest of radio EXTA FREE transmitters
is analogous.
CAUTION: Every transmitter can cooperate with ROP-01 in a different mode, depending on how they were added to
the device. One transmitter can be added during one programming cycle. Full memory is signalled with pulsating LED red diode.
Press transmitter’s
push-button for
a longer time.
Press the transmitter’s push-button
for a longer time. LED red diode
switches on (first signal pulsates,
next the signal is constant).
Press transmitter’s push-button and then
release it. LED red diode switches on
(first signal pulsates, next
the signal is constant).
Press and release transmitter’s
push-button. LED red diode
switches on (first signal pulsates, next
the signal is constant).
Release transmitter’s push-
button. LED red diode switches
on (first signal pulsates,
next the signal is constant).
Release transmitter’s push-button.
LED red diode switches on (the
signal pulsates), next the LED red
diode switches off - it means the
TRANSMITTER IS ADDED.
Press and release the same transmitter’s
push-button. LED red diode switches on
(signal pulsates) and then switches off -
THE TRANSMITTER IS ADDED.
Press and release the same transmitter’s
push-button. LED red diode switches on
(the signal pulsates) and next it switches
off - THE TRANSMITTER IS ADDED.
Press the same transmitter’s push-
-button and release it. LED red
diode switches on (the signal pulsa-
tes) and next it switches off - THE
TRANSMITTER IS ADDED.
Press PROG push-button of ROP-01 device
for a longer time until LED red diode
switches on (constant signal).
Next release PROG push-button.
Press PROG push-button of ROP-01 device
for a longer time until LED red diode
switches on (constant signal).
Next release PROG push-button.
Press PROG push-button of ROP-01 device
for a longer time until LED red diode
switches on (constant signal).
Next release PROG push-button.
Press PROG push-button of ROP-01 device
for a longer time till LED red diode
switches on (constant signal).
Next release PROG push-button.
Maximum time is 18 hours.
Press PROG push-button of ROP-01 device for a longer time till
LED red diode switches on (constant signal). Next release PROG
push-button. Wait (for about 5 seconds) till LED red diode switches
on (first signal pulsates, next the signal is constant).
After the adjusted time is
finished (the number
of LED red diode flashes)
press PROG push-button
and then release it
- TIME IS ADDED.
Press PROG push-button of ROP-01 device
and then release it. LED red diode switches
off and then switches on (signal pulsates).
Every LED diode pulse equals 1 second.
Press PROG push-button of ROP-01
device for a longer time.
After 5 seconds LED red diode switches on
(signal pulsates) and then it switches off.
Release the push-button in ROP-01 -
MEMORY IS DELETED.
1s 2s
ns
