DESCRIPTION
MAIN MENU
T1 AND T2 TIME ADJUSTMENT
EXTERNAL INPUT ADJUSTMENT
BACKLIGHT LEVEL ADJUSTMENT
OPERATING MODE ADJUSTMENT
Displayed elements and messages description
- relay mode
- t1 and t2 time adjustment
- switch on/switch off
- automatic mode
- operating mode adjustment
- manual mode
- backlight level adjustment
- external input S
- permanent switch on / switch off input
- external input IN
- waiting for releasing signal
- backlight
- operating mode end
Push button description
• main window – automatic mode entry
• main window – manual mode entry or relay mode change if the clock is already in the manual mode
• main window – main menu entry
• different windows - submenu entry or adjusted value confirmation
• menu windows/options change or decreasing/increasing the adjusted value
Choose OK to enter menu; use cursor to choose options.
Function Description
OPERATING MODE ADJUSTMENT
T1 TIME ADJUSTMENT
T2 TIME ADJUSTMENT
EXTERNAL INPUT ADJUSTMENT
BACKLIGHT LEVEL ADJUSTMENT
- time preview and adjustment; press OK to enter;
adjusted time preview window, press OK to enter;
HOUR - use cursor to choose the required number of hours; adjustment range from 0 to 99; press OK to confirm;
MINUTE - use cursor to choose the required number of minutes; adjustment range from 0 to 59; press OK to confirm;
SECOND - use cursor to choose the required number of seconds; adjustment range from 0 to 59; press OK to confirm;
DECIMAL POINT OF A SECOND - use cursor to choose the required value; adjustment range from 0 to 90; press OK to confirm;
To confirm all the adjustments press OK; confirming the command allows to enter the time adjustment window.
The system is equipped with protection against 0h0m0s0ss - 0,1 sec is the minimum time.
time adjustment in
menu - similarly to
menu.
- system mode adjustment suitable for the moment of releasing
external input IN; the system operates in this mode as long as there is a
releasing signal on external input IN; press OK to enter; use cursors to
choose a suitable mode for the external input, where:
- external input function is switched off;
- manual mode with a relay constantly switched off;
- manual mode with a relay constantly switched on;
Use cursors to change options; press Ok button to confirm choices.
After the signal in releasing input IN disappears, the previous operating mode
(time measure) will be finished.
There is an escape possibility from every submenu window one level high-
er in every moment of programming by pressing or without saving the
adjusments.
- backlight level adjustment; press OK to enter;
- the backlight switches on after pressing any of the buttons, and it will
be switched off automatically after 20 seconds from the last press;
- the backlight will be switched on as long as the system is connected to
power supply voltage;
- the backlight will be switched off.
Use cursors to change options; press OK to confirm your choices.
There is an escape possibility from every submenu window one level higher
in every moment of programming by pressing or without saving the
adjusments.
There is an escape possibility from
every submenu window one level
higher in every moment of program-
ming by pressing or without sav-
ing the adjusments.
- operating mode adjustment will be activated in the moment of releasing external
input S; press OK to enter;
Use cursors to choose the right mode; the modes are numbered in the range from
to
, press OK to confirm your choice;
Confirming the command allows to enter the operating mode adjustment window.
There is an escape possibility from every submenu window one level higher in every moment of
programming by pressing or without saving the adjusments.
Power supply voltage release:
for
for
and
SWITCH ON DELAY - after the supply voltage has been
applied the preset time t measure starts. After the time is
over the relay switches on (pos. 11-14). The next switch
on mode appears after power supply voltage reset.
SWITCH ON DELAY - after the supply voltage has been
applied the t
1
time measure starts. After the time is over
the relay switches on (pos. 11-14) for t
2
time. The next
switch on interval appears after power supply voltage
reset.
SWITCH OFF DELAY - after the supply voltage has been
applied, the relay switches on immediately (pos.11-14),
and the preset time t is measured. After the preset time
is measured, the relay is switched off (pos.11-12). The next switch on interval appears after power
supply voltage reset.
SWITCH OFF DELAY - after the supply voltage has
been applied, the output relay switches on immediately
(pos.11-14), and the preset time t
1
is measured. After the
preset time is measured, the relay is switched off (pos.11-
12) for the preset t
2
time and its another switch on mode. The next switch on interval appears after
power supply voltage reset.
FLASHER STARTING WITH OFF – (Starting from the
switch off position). After the supply voltage has been
applied, the preset time t is measured. After the time is
over, the relay switches on (pos. 11-14). Again with the preset time t interval, the relay is switched
off (pos.11-12) and switched on (pos. 11-14). The next switch on interval appears after power supply
voltage reset.
FLASHER STARTING WITH OFF – (Starting from the
switch off position). After the supply voltage has been
applied, the preset time t
1
is measured. After the time is
over, the relay switches on (pos. 11-14) for the preset t
2
time and again switches off (pos.11-12) for the
preset t
1
time. The next switch on interval appears after power supply voltage reset.
FLASHER STARTING WITH ON – (Starting from the
switch on position). After the supply voltage has been
applied, the relay is immidiatelly switched on (pos. 11-14)
and the preset time t is measured. After the time t is over, the relay switches off (pos. 11-12). Again
with the preset time t interval the relay is switched on (pos. 11-14) and switched off (pos. 11-12). The
next switch on interval appears after power supply voltage reset.
FLASHER STARTING WITH OFF – (Starting from the
switch on position). After the supply voltage has been ap-
plied, the output relay switches on immediately (pos.11-
14) for the preset time t
1
. After the time is over, the relay is swtches off (pos.11-12) for the preset
t
2
time and its another switch on mode for t
1
time. The next switch on interval appears after power
supply voltage reset.
IMPULSE GENERATOR DELAY 0,5 sec. - After the sup-
ply voltage has been applied the preset time t measure
starts. After the time t is over the relay switches on (pos.
11-14) for 0,5 second, and switches off (pos. 11-12). The
next switch on interval appears after power supply voltage reset.
PERMANENT SWITCH ON MODE - After the supply vol-
tage has been applied the relay is switched on permanen-
tly. When choosing this mode t
1
and t
2
time adjustments
do not matter.
PERMANENT SWITCH OFF MODE - After the supply
voltage has been applied the relay is switched off per-
manently. When choosing this mode t
1
and t
2
time adjust-
ments do not matter.
TIME IMPULSE RELEASED BY RISING EDGE – after
the impulse release has been applied to the power-supply
system (rising edge) it switches on the relay (pos. 11-14)
and starts to measure the preset time. After the time t is over the relay is switched off (pos. 11-12).
Impulse time duration is not important here.
SWITCH ON/OFF DELAY- (retriggerable) – after the im-
pulse release has been applied to the power-supply sys-
tem (rising edge), it lets the relay be switched off (pos.
11-12) and at the same time, starts the preset time t
1
measurement. After the time is over the relay
is switched on (po. 11-14). After the impulse release fade is detected (falling modulated voltage), the
system starts preset t
2
time measuremnt and after it is over the relay is switched off (po. 11-12). In case
the impulse release duration is shorter than the preset time t
1
, the relay is not switched on. Applying
the impluse release during the preset t
2
time measurement does not cause switching off the relay but
it starts time measurement after the impulse fade (falling modulated voltage).
TIME IMPULSE RELEASED BY FALLING EDGE – po-
wer-supply system switches on the relay after impulse re-
lease fades (falling edge) (pos.11-14) and time measure-
ment starts. After the time t is over the relay is switched off (pos. 11-12). The following impulse release
fades during time measurement does not cause time measure from the beginning (non- retriggerable).
SWITCH ON/OFF DELAY- (non-retriggerable) – after the
impulse release has been applied to the power-supply
system (rising edge), it lets the relay be switched off (pos.
11-12), at the same time, starts the preset time t
1
measurement. After the time is over the relay is swit-
ched on (pos. 11-14). After the impulse release fade is detected (falling modulated voltage), the system
starts preset time t
2
measuremnt and after it is over the relay is switched off (po. 11-12).The release
input state can change during the time t
2
measurement and does not affect functioning of the system
In case the impulse release duration is shorter than the preset time t
1
, the relay is not switched on.
SWITCH ON/OFF DELAY – after the impulse release has
been applied to the power-supply system (rising edge),it
lets the relay be switched off (pos.11-12) and at the same
time starts the preset time t measurement. After the time is over the relay is switched on (pos.11-14).
After the impulse release fade is detected (falling edge), again the system starts the preset time me-
asurement. When it is over the relay is switched off (pos. 11-12). In case the impulse duration time is
shorter than the preset time t, the relay is switched on only for the time t.
IMPULSE GENERATION WITH AN ALTERNATE TIME
DURATION - after the impulse release has been applied
to the power-supply system (growing value), it switches
on the relay for the preset time t
1
, and switches it off. The next impulse release causes the relay swit-
ches on for t
2
time. Another one switches on the relay for t
1
time, etc. The impulse release time duration
does not influence the relay switching on time.
BISTABLE RELAY WITH TIME LIMIT – after the impulse
release has been applied to the power-supply system (ri-
sing edge), it switches on the relay (pos.11-14) and starts
to measure the preset time t. The relay is switched off
during the next impulse release (rising edge) or after time t is over in case there was no such impulse
occurence. Impulse time duration is not important for system operating.
SWITCH OFF DELAY RELEASED BY FALLING EDGE
- after the impulse release has been applied to the po-
wer-supply system, it switches on the relay (pos. 11-14).
Impulse release fade causes the preset time t
1
measurement, after it is over the relay is switched off
(po. 11-12) for the preset time t
2
. During the t
2
time the system is resistant to signals release. After the t
2
time is over the relay is switched on again in the moment of applying impulse release (growing value).
TIME IMPULSE RELEASED BY RISING EDGE WITH
SWITCH OFF DELAY (non-retriggerable) - after the
impulse release has been applied to he power-supply
system (rising edge) it switches on the relay (pos.11-14).
After the impulse release fade is detected (falling modulated voltage), the system starts the preset time
t measurement and when the time is over the relay is switched off (pos. 11-12).
IMPULSE RELEASED BY FALLING EDGE - after the
impulse release has been applied to the power-supply
system (rising edge), it switches on the relay for the pre-
set time t
1
, and after the time elapses it switches off the relay. The impulse release fade (falling edge)
switches on the relay (pos. 11-14) for the preset time t
2
, and after the time elapses it switches it off.
During switching on the relay the rising edge and the falling edge are ignored.
SWITCH ON DELAY RELEASED BY IMPULSE - after
the impulse release has been applied to the power-supply
system (rising edge) it keeps the relay in a switched off
position (pos.11-12) and simultaneously starts the preset
time t measurement. After the time t is over the relay is
switched on (pos. 11-14). The relay is switched on as long as there is a power supply voltage on, the
next release impulses do not affect operation of the relay.
STAR-DELTA SWITCH - after the supply voltage has
been applied the relay 1 is switched on (pos. 11-14) for
the preset time t
1
. After the time is over the relay is swit-
ched off and the preset time t
2
is measured. After time
t
2
is over the relay 2 is switched on permanently (pos.
21-24).
U
11-14
21-24
t1
t2
t
External signal S release:
for
for
and
TIME IMPULSE RELEASED BY RISING EDGE WITH
SWITCH OFF DELAY (retriggerable) - after the impulse
release has been applied to the power-supply system (ri-
sing edge) it switches on the relay (pos.11-14). After the
impulse release fade is detected (rising edge), the system starts the preset time t measurement and
when the time is over the relay is switched off (pos. 11-12). The following impulse release fade during
time measurement causes time measure from the beginning (retriggerable).
TIME IMPULSE RELEASED BY IMPULSE WITH SPE-
CIFIC TIME DURATION - after the impulse release has
been applied and lasts continuously for the preset time
t
1
, it switches on the relay (pos.11-14) for time t
2
. If the
release impulse is shorter than the preset time t
1
, the relay is not switched on - during switching on the
relay the releasing impulses are ignored.
S
t1
t1
t2
t2
11-14
S
U
t
11-14
S
t
t
11-14
S
t
t
t
t
t
11-14
S
t
t
t
11-14
S
t
t
t
t
t
11-14
S
t
t
11-14
S
t
t
11-14
U
0.5s
t
0.5s
t
11-14
U
t
t
t
t
t
t
11-14
U
t
t
t
t
t
t
11-14
U
t
t
11-14
U
t
t
11-14
S
t1
t1
t2
11-14
S
t
t1
t2
t
t1
11-14
S
t1
t2
t1
11-14
S
t1
t1
t2
11-14
S
t1
t1
t2
11-14
U
11-14
U
11-14
U
t1
t2
t1
t2
t2
t1
11-14
U
t2
t1
t2
t1
t2
t1
11-14
U
t1
t2
t2
t1
11-14
U
t2
t1
t1
t2
11-14
