230 V AC
14 V DC
CAUTION ! The device is designed for single-phase installation and must be installed
in accordance with standards valid in a particular country. Installation, connection
and control should be carried out by a qualified electrician staff, who act in accord-
ance with the service manual and the device functions.
1. Disconnect power supply by the phase fuse, the circuit-breaker or the switch- discon-
nector combined to the proper circuit.
2. Check if there is no voltage on connection cables by means of a special measure equip-
ment.
3. Connect the power supply to 230 V AC.
4. Connect the cables to the appropriate control terminals in accordance with the con-
nection diagram (in case of radio control only, it is not required to connect the cables to
IN1, IN2 terminals).
5. Mount the controller in the Ø60 junction box.
6. Switch on the power supply from the mains.
7. Add selected transmitters to the controller (a description is in TRANSMITTERS’ PRO-
GRAMMING section) and check their proper functioning.
SLR-01 controller is designed for cooperation with monochrome LEDIX standard lamps
and with other LED products supplied with 10÷14 V DC (monochrome tapes, LED strips
and modules, LED lamps). The controller controls the functions: switching on/ switching
off by means of one or two buttons, brightening/dimming and automatic switching off
after a programmed time (with gradual dimming within 10 s).
The controller features:
• to control a standard monochrome LED fittings of the LEDIX system,
• to control other monochrome LED products supplied with 10÷14 V DC,
• to carry out the functions: switching on/ switching off, brightening/dimming, timer
mode with turning off,
• radio control (transmitters of EXTA FREE system) or wired control system (inputs IN1,
IN2),
• PWM output of the MOSFET transistor – maximum current capacity of 4 A,
• 9-bit fast PWM outputs allow the brighting/dimming function to be very fluent,
• low power consumption in the standby mode (0.25 W) – controller is designed for con-
tinuous operation (ECOLINE).
TECHNICAL DATA
MOUNTING
DESCRIPTION
DIAGRAM
APPEARANCE
Nominal supply voltage:
10 ÷ 14 V DC
Nominal power consumption:
0,22 W
Number of channels:
1
Maximum current in the channel:
4 A
Controlling signal:
PWM 9-bit
Number of wired outputs:
2 (IN1, IN2)
Radio transmission:
868,32 MHz
Transmission method:
One-way without confirmation
Coding:
Yes – transmission with addressing
Maximum number of transmitters:
32
Range:
Up to 230 m in the open area
Time adjustment:
1 s ÷ 18 h
Number of connection terminals:
6
Maximum cross-section of connection cables:
Up to 2,5 mm
2
Ambient temperature range:
-10 ÷ +55
o
C
Mounting:
In a Ø60 junction box
Casing protection degree:
IP20
Protection class:
III
Dimensions:
47,5 x 47,5 x 20 mm
Weight:
25 g
Reference standard:
PN-EN 60669; PN-EN 61000
CAUTION! Nominal output voltage of the power supply (10÷14 V DC) and its nominal
output power must be adjusted for LED light source connected to the controller.
Wired control terminals
(IN1, IN2)
Output terminals (+, -)
Power supply terminals (+, -)
Optic signalling of the
controller’s operation
Programming button
MAXIMUM CURRENT CAPACITY:
Up to 40 W for LED diode products supplied with 10 V
Up to 48 W for LED diode products supplied with 12 V
Up to 56 W for LED diode products supplied with 14 V
ZNP, ZNN or ZNM series of the
power supply in 14 V DC version
Example of the
LEDIX series
LED fitting
