Z-Band Z-RF Encode 001 Скачать руководство пользователя страница 17

Страница: 17 / 18

Z-RF Encode 001 Manual V.1

Rev 5.4.21

EAS Support

EAS

This is equipped with EAS terminals / connections and CVBS (Composite Video Input) and L/R audio input

connections on the rear panel of the device.

If applicable, connect your EAS (Alert Device System) outputs to the Encoder.

If the encoder receives the

proper Event signal from your EAS device, the normal input audio/video program will be replaced by the
audio and video from the EAS system device. Once the encoder has received the proper signal from your

EAS device the normal input video and audio will return to a normal operating mode.

****THIS DEVICE IS NOT AN EAS RECEIVER****

Note: It is the responsibility of the Installer/User to properly connect, verify, and test the EAS functionality of this

device with the EAS receiver.

Note: It is the responsibility of the Installer/User to properly perform the required EAS tests as required by the

FCC or your specific Government Agency.

If the EAS functions on this device fail for any reason it is the responsibility of the Installer/User to replace this

device as required by the FCC or your specific Government Agency.

Содержание Z-RF Encode 001



















Результаты поиска

Содержание Z-RF Encode 001

Отзывы:

Похожие инструкции для Z-RF Encode 001

Бренды по названию

Популярные бренды

Z-Band Z-RF Encode 001, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание Z-RF Encode 001

Отзывы:

Похожие инструкции для Z-RF Encode 001

Бренды по названию

Популярные бренды