Revised 03-11-10
YUNCA FUZiON FEBRUARY 2010
Page 9 of 19
FUZiON INFRA-RED REMOTE CONTROL with AUTO TIMER.
POWER ON / OFF:
First check that the two AAA batteries are inserted. The remote may appear to
be on, but it is likely that is not so. The remote control is protected with a “kiddy lock”. To turn it on
press and hold the
POWER
button for about 2 seconds until “off” disappears from the screen, then
release (to unlock the safety feature), and quickly give one short press of the
POWER
button. This
will turn on power to the remote control, and will also start the fire in the MANUAL - HIGH setting.
Current mode / settings will be displayed. The fire will always start in manual operating mode on a
high setting. (Also refer to the next page for further information). There is an audible beep when the
fire receives a signal from the remote, range is approximately 5 metres.
CLOCK SETTING:
Press the
CLOCK
button once (“clock” in the display will start flashing). Press
WEEK
to set the week day, press
HOUR
to set the hour, taking care to check if on a.m. or p.m.
Press
MIN
to set the minute (holding the button down will advance the minutes quicker). Press
CLOCK
to save the setting.
MANUAL “FLAME” OPERATING MODE
has three settings: High, Medium, Low. Heat output is
fixed to the setting and needs to be adjusted manually by pressing
TEMP
control “ – “ and “ + “
buttons.
“FUZZY LOGIC” OPERATING MODE
replaces the traditional thermostat operation with six “comfort
levels”. Press
MODE
to switch between
Manual
and
Fuzzy Logic
, and use the
TEMP
“
–
“ and “
+
“
buttons. Choose the comfort level that best suits your needs. Every now and then the fire will give a
short boost of heat and then return to your chosen setting. This is the most economical way to
operate your Yunca Fuzzy Logic control fire.
HINT
: The two speed fan is designed to quickly transfer heat around the room and ensures the most
economic gas use. The three-position switch (LOW/OFF/HIGH) is located under the front hearth panel, to the
right of the manual control.
AUTO FUNCTION
:
To set this feature you will need to ensure the remote control is on (as advised above),
and ensure the
CLOCK
time and day are correctly set.
PLEASE NOTE:
If a key is not pressed for 7 seconds,
the programming will “time out” and you will need to re-start the process.
Set times to Start and/or Stop the fire with a choice of up to two daily programme settings (
PROG1
and
PROG2
). You can choose to use only
PROG1
if only one setting is needed. Heat output on Auto is initially run
in manual control, and once the fire is operating you can then switch to the more economical Fuzzy Logic.
EXAMPLE
: Set
PROG1
to start at 6:00 am, stop at 8.00am. Set
PROG2
to start at 4.30pm, stop at 10.30pm
Monday to Friday. Both
PROG1
and
PROG2
may have different settings programmed for the weekend if
required.
TO SET:
Press
PROG1
to set the “timer on” setting (Mon-Fri). Now choose the desired heat output (High,
Med or Low) Press
HOUR
button, making sure you have chosen the correct a.m. or p.m. time, then press
MIN
button (increases in 10 minute steps) to set the start time. Press
PROG1
again and use the
HOUR
/
MIN
buttons to set the stop time. Press
CANCEL
at any time to clear the setting currently on screen (i.e.either
Start or Stop). If you are not setting weekend programming, just press
PROG1
to save your settings and exit
the programming function.
If you wish
PROG1
to operate on Saturday and Sunday, press
WEEK
button to set start time, using
HOUR
and
MIN
buttons as described above. Then press
PROG1
again to set the weekend stop time, and press
PROG1
once more
to save your settings and exit the setting mode.
Continue as above using
PROG2
if required. To check the programme settings press either Prog1 or Prog2.
…Important Info
continued on page 10…