Yukon Eagle LWG-112 Скачать руководство пользователя | Manualshive

Страница: 5 / 64

background image

5

Unpack and Check Your Cartons

INSPECT SHIPMENT

Your furnace is shipped complete in three cartons.
Note any damage to the shipping cartons. Remove all
items from your shipping cartons. Check all items
against the packing list below. Note any items lost or
damaged in shipment. Refer to the exploded view and
parts list in the back of the manual for the part names
and numbers of missing or damaged items

.

Keep the

small parts in the parts bag until you are ready to
install them.

PACKING LIST

1. Carton One:

The basic furnace comes in the crate.

Inside the filter door, below the flue outlet, is the pre-
assembled, circulating fan, motor, belt, drives and drip
shield. The air filter lies in a frame above the fan.
Inside the furnace wood-firing door are:

• Three wood grates (installed)
• Secondary air shut-off assembly
• Smoke pipe draw collar (Polar Unit Only)
• Primary air draft tube
• Door handle weldment and handle assembly for both

fire door and ash pan.

Remove these items and set aside for later installation.

2. Carton Two:

This accessory package contains the

following items:

• Secondary air intake cover
• Thermostats
• Barometric damper
• Fan and limit control
• Damper control unit
• Transformer
• Wiring harness
• Fume sensor (gas only)
• Owner's manual
• Warranty sheet
Remove these items and set aside for later installation.

3. Carton Three:

The oil or gas burner is in this

carton. It is pre-assembled and ready for installation.

Questions? Visit www.yukon-eagle.com or call 1-800-358-0060

FIG. 1

«
...
3
4
5
6
7
...
»

Содержание LWG-112

































































Отзывы:

Нет отзывов

Похожие инструкции для LWG-112

Бренд: Carbolite Gero Страницы: 58

Бренд: Bryant Страницы: 6

Бренд: Rinnai Страницы: 6

Бренд: Rinnai Страницы: 68

Бренд: Lacunza Страницы: 16

Бренд: Hamilton Страницы: 64

Бренд: Lennox Страницы: 54

ALPHA FURNACE 2014

Бренд: ALPHA PLAM Страницы: 9

Бренд: Williams Страницы: 40

CeramicMaster E1000

Бренд: VOP Страницы: 23

Бренд: UPG Страницы: 16

Бренд: Johnson Furnace Страницы: 16

Бренд: HHP Страницы: 19

Бренд: Ingersoll-Rand Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды