Yukon Eagle LWG-112 Скачать руководство пользователя

Страница: 2 / 64

D A N G E R

RISK OF FIRE OR EXPLOSION

Do not burn garbage, gasoline, drain oil, kerosene, thinners, etc.

WARNING

RISK OF FIRE

Tightly close the firing door and ash door during operation.

Do not operate with flue draft exceeding .03" W.C.

Do not store flammable materials within marked installation clearance.

Frequently inspect and clean soot and/or creosote from the heat exchanger,
smoke pipe, and chimney.

Do not connect this unit to a chimney flue serving another appliance.

CAUTION

BLACK SURFACES ARE HOT

Keep children away. Do not touch.

Questions?

Visit www.yukon-eagle.com

or call

1-800-358-0060

For repair or replacement parts,

See back cover for details.

Before installing this
furnace, read and follow all
instructions in this manual.
It is recommended that a
heating professional installs
or supervises the entire
installation of the furnace,
ducts, chimney, electrical
and gas or oil hook ups.

FOR YOUR SAFETY:

If you smell gas:

1. Open windows
2. Do not touch electrical switches
3. Extinguish any open flame
4. Immediately call your gas supplier

FOR YOUR SAFETY:

Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.

Содержание LWG-112

































































Результаты поиска

Содержание LWG-112

Отзывы:

Похожие инструкции для LWG-112

Бренды по названию

Популярные бренды

Yukon Eagle LWG-112, Руководство пользователя

Результаты поиска

Содержание LWG-112

Отзывы:

Похожие инструкции для LWG-112

Бренды по названию

Популярные бренды