background image

i

T H I S   PA G E   L E F T   I N T E N T I O N A L L Y   B L A N k

WA R R A N T Y

The YSI Professional OBOD

®

 (ProOBOD

TM

) probe and cable assembly is warranted

for two (2) years from date of purchase by the end user against defects in materials and 

workmanship, exclusive of batteries and any damage caused by defective batteries. 

ProOBOD sensor caps are warranted for one (1) year from date of purchase by the end 

user against defects in material and workmanship.  ProOBOD systems (instrument 

& cable/probe assemblies) are warranted for 90 days from date of purchase by the 

end  user  against  defects  in  material  and  workmanship  when  purchased  by  rental 

agencies for rental purposes.  Within the warranty period, YSI will repair or replace, 

at its sole discretion, free of charge, any product that YSI determines to be covered 

by this warranty.

To  exercise  this  warranty,  call  your  local  YSI  representative,  or  contact  YSI 

Customer Service in Yellow Springs, Ohio at +1 937 767-7241, 800-897-4151 or visit 

www.YSI.com for a Product Return Form.  Send the product and proof of purchase, 

transportation prepaid, to the Authorized Service Center selected by YSI.  Repair 

or  replacement  will  be  made  and  the  product  returned,  transportation  prepaid.  

Repaired or replaced products are warranted for the balance of the original warranty 

period, or at least 90 days from date of repair or replacement.

LIMITATION OF WARRANTY

This Warranty does not apply to any YSI product damage or failure caused by: 

Failure to install, operate or use the product in accordance with YSI’s written 

1. 

instructions; 

Abuse or misuse of the product;

2.

Failure to maintain the product in accordance with YSI’s written instructions

3.

or standard industry procedure;

Any improper repairs to the product;

4.

Use  by  you  of  defective  or  improper  components  or  parts  in  servicing  or

5.

repairing the product;

Modification of the product in any way not expressly authorized by YSI.

6.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR 

IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS 

FOR A PARTICULAR PURPOSE.  YSI’S LIABILITY UNDER THIS WARRANTY 

IS  LIMITED  TO  REPAIR  OR  REPLACEMENT  OF  THE  PRODUCT,  AND  THIS 

SHALL  BE  YOUR  SOLE  AND  EXCLUSIVE  REMEDY  FOR  ANY  DEFECTIVE 

PRODUCT  COVERED  BY  THIS  WARRANTY.    IN  NO  EVENT  SHALL  YSI  BE 

LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL 

DAMAGES  RESULTING  FROM  ANY  DEFECTIVE  PRODUCT  COVERED  BY 

THIS WARRANTY.

Содержание WE KNOW ProOBOD












Отзывы: