YSI 85 Скачать руководство пользователя | Manualshive

Страница: 20 / 60

background image

Advanced Conductivity Setup

Section 6

YSI, Incorporated

Model 85

16

6.2 CHANGING THE REFERENCE TEMPERATURE

Follow these steps to modify the reference temperature of the Model 85.

1.

Turn the instrument on and wait for it to complete its self-test procedure.

2.

Use the

MODE

button to advance the instrument to display conductivity.

3.

Press and release both the

DOWN ARROW

and the

MODE

buttons at the same time.

The

CAL

symbol will appear at the bottom left of the display. The large portion of the display will

show

1.91 %

(or a value set previously using Advanced Setup).

4.

Press and release the

MODE

button; the large portion of the display will show

25.0C

(or a

value set previously using Advanced Setup).

5.

Use the

UP ARROW

or

DOWN ARROW

button to change the value to the desired new

reference temperature (any value between 15

o

C and 25

o

C is acceptable).

6.

Press the

ENTER

button. The word “

SAVE

” will flash across the display for a second to

indicate that your change has been accepted.

7.

The instrument will automatically return to normal operation mode.

6.3 CHANGING FROM AUTORANGING TO MANUAL RANGING

If your application is easier to perform using a manual range that you select, the YSI Model 85
allows you to turn off the default autoranging feature. While you are making conductivity or
temperature compensated conductivity measurements, simply press and release the

UP ARROW

button. Each additional press of the

UP ARROW

button will cycle the Model 85 to a different

manual range until you return again to autoranging. Five pushes of the

UP ARROW

button will

cycle the Model 85 through the four manual ranges and return the instrument to autoranging.

NOTE:

You may see an error message in some manual ranges if the manual range selected is not

adequate for the sample you are measuring. If this happens, simply press and release the

UP

ARROW

button again until a range is selected which is suitable for your sample. If you get lost and

don’t know if you’re in a manual range or autoranging, simply turn the instrument off and back on.
Also note that the conductivity units will flash while you are in manual range. The instrument will
always default to autoranging when first turned on.

The four ranges of the YSI Model 85 are:

Range 1

Range 2

Range 3

Range 4

0 to 499.9

µ

S/cm

0 to 4999

µ

S/cm

0 to 49.99 mS/cm

0 to 200.0 mS/cm

«
...
18
19
20
21
22
...
»

Содержание 85





























































Отзывы:

Нет отзывов

Похожие инструкции для 85

Бренд: Samson Страницы: 4

Бренд: X-Rite Страницы: 80

Бренд: Nellcor Страницы: 104

Бренд: Olympus Страницы: 12

Бренд: Tavool Страницы: 12

Бренд: Oldham Страницы: 96

XL4 SECOND STAGE

Бренд: Apeks Страницы: 21

Бренд: Water I.D. Страницы: 56

Бренд: Meec tools Страницы: 23

NetSure M832DNA

Бренд: Vertiv Страницы: 176

Бренд: Hammond Страницы: 36

Бренд: SIMET Страницы: 2

Бренд: YZXStudio Страницы: 3

Бренд: Suaoki Страницы: 79

zelsius C5 -IUF

Бренд: Zenner Страницы: 28

Бренд: R&S Страницы: 46

Бренд: General Страницы: 16

Бренд: WIKA Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды