background image

1.3 Regular maintenance activities for which the user is respon‐

sible

1.3.1 Maintenance Schedule

The air conditioning unit is designed to require as little maintenance as possible. Nevertheless, to ensure

smooth operations with a minimal use of electricity, a long working life and compliance with the regula‐

tions of each country, regular maintenance inspections must be made.
Johnson Controls Inc. shall not be considered responsible for any damage caused by improper mainte‐

nance of the unit, which includes anything inconsistent with that described in this document or others

specifically provided with the unit.
To make them easier, maintenance tasks have been grouped by time intervals in a series of tables.

Maintenance responsibilities of the user

, see on page 25.

1.3.2 Maintenance responsibilities of the user

Like any other machine, the HVAC unit requires regular maintenance, as the wear to which some of its

parts are subjected can effect its mechanical reliability and the safety of those responsible for its main‐

tenance.
In compliance with current regulations, the unit must be regularly inspected and the results recorded on

the forms provided by the Labour and Health Authorities of the country where the HVAC unit is installed.
Users cannot access this form to perform maintenance and upkeep tasks on the unit.
There is no intent for the user to perform any maintenance tasks on the HVAC unit.

User manual

1

Regular maintenance activities for which the user is responsible

1.3

25

Содержание YLHA 50





























Отзывы: