York YCAV0569 Скачать руководство пользователя страница 159

Страница: 159 / 278

159

JOHNSON CONTROLS

FORM 201.21-NM2 (616)

VSD TEMPERATURE CONTROL, OPERATION OF THE COOLANT PUMP,

AND VSD CABINET COOLING FANS

The Coolant pump and VSD Cabinet Cooling Fans will

run to cool the VSD whenever any of the following

conditions are met:

VSD Comp IGBT Baseplate Temperature on a 2 or

4 compressor unit is greater than 10°F below the

cutout (Cutout [218°F]-10°F =208°F). When the

VSD internal ambient falls below the restart tem-

perature (Cutout [218°F] - 15°F = 203°F), the fans

and pump will turned off without a time delay.

VSD Comp IGBT Baseplate Temperature on a 3

compressor unit is greater than 10°F below the

cutout (Cutout [232°F] - 10°F = 222°F). When

the VSD internal ambient falls below the restart

temperature (Cutout - 15°F = 217°F), the fans and

pump will be turned off without a time delay.

Pre-charge Enable 1 from the Chiller Logic Board

is ON.

Pre-charge Enable 2 from the Chiller Logic Board

is ON.

VSD Internal Ambient Temp > 158°F (Cutout)

– 10°F = 148°F. When the Internal Ambient Temp

falls < 158°F (Cutout) - 15°F = 143 °F the VSD

cooling fans and glycol pump will turn off.

Condenser Fans (as needed) and VSD coolant pump/

fans will run whenever a compressor is running.

Under these conditions, the condenser fans will run

to control discharge pressure and the VSD coolant

pump/fans will run to cool the IGBT baseplate and

internal cabinet. Additional condenser fans will be

brought on, if the IGBT baseplate temperatures or

internal cabinet ambient rises to 5°F below the cut-

out. Condenser fans will turn off, if the compressor

turns off provided VSD cooling is not required. The

glycol pump and cabinet fan may continue to run,

if VSD cooling is required.

Glycol Pump and Cabinet Cooling Fans will also

run in the Service Mode if the Fan/Pump Run Bit

is Set.

Содержание YCAV0569























































































































































































































































































Результаты поиска

Содержание YCAV0569

Отзывы:

Бренды по названию

Популярные бренды

York YCAV0569, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание YCAV0569

Отзывы:

Бренды по названию

Популярные бренды