manualshive.com logo in svg

York YB, Руководство по эксплуатации

Поделиться
Скачать
York YB Скачать руководство пользователя страница 22

YORK INTERNATIONAL

22

FORM 160.60-O2 (1004)

PanelView Plus 1000 Control Center

 DISPLAY

Starts/Hours

Displays the total number of engine starts and total hours 
of operation to date

  Calculated  Engine  Load

Displays the engine load calculated from  manifold pres-
sure and RPM readings, in percent

Throttle Position

 

Displays the throttle position from fully open to fully 
closed in percent

Oil Pressure (Graphical)

Displays the engine oil pressure in psig

Manifold Pressure (Graphical)

Displays the engine manifold pressure in psia

RPM

Displays engine rpm

  Water  Jacket  Temperature  (Graphical)

Displays the water jacket temperature in º F

Days Run Time Before Maintenance

Displays the number of days operational time remaining 
before scheduled maintenance

Clutch  Solenoid Output

Indicates the status of the clutch solenoid

Clutch  Engaged/Disengaged

Indicates the status of the clutch

Ignition Enable

Indicates that the engine ignition system is active

Engine  Run

Indicates the engine is operating

Starter

Indicates that the starter motor is operating

 Crank  Terminate  Signal

Indicates that the engine control panel has issued a signal 
to the main panel to terminate engine crank

 Water Jacket Temperature Signal

Indicates whether or not the water jacket temperature 
has exceeded safe limits

 ENGINE SCREEN

LD09889

FIG. 15 -  ENGINE SCREEN 

Содержание YB

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды