background image

JOHNSON CONTROLS

12

FORM 145.05-SU2 (1207)

This feature enables the unit to lower the supply air 

temperature to prevent the supply air dew point from 

dropping below the under floor temperature.

Field Wiring

A 10K Type II thermistor must be located in the under 

floor space and connected to IN-6 terminals 11 and 12 

of the main control board.

Programming

The following items must be programmed through the 

Setpoints

” section of the User Interface:

• 

“AC-S/A Dew En”

 must be set to ON

FLEXSYS DEW POINT TEMPERATURE CONTROL

• 

“AC-S/A Dew Min”

 set point must be pro-

grammed.  The default value is 48.0˚ F.  This is 

the lowest supply air temperature the control can 

use for dew point control.

• 

“AC-S/A Dew Max”

 set point must be pro-

grammed.  The default value is 60.0˚ F.  This is 

the highest supply air temperature the control can 

use for dew point control.

• 

“AC-S/A Dew Dif”

 set point must be pro-

grammed.  The default value is 5.0˚ F.  This value 

is subtracted from the under floor temperature 

and is used to establish a under floor dew point 

supply air temperature set point.

Содержание VERSECON YSWU Series

















Отзывы: