York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 44 / 160

JOHNSON CONTROLS

FORM 160.79-O3

ISSUE DATE: 11/09/2018

SECTION 2 – OPTIVIEW CONTROL CENTER

This screen displays a cutaway of the compressor #1 or

#2, revealing the impeller. Animation of the impeller

indicates when the compressor is running. Parameters

related to the compressor are displayed here. Also,

compressor manual control functions are performed

here. The Pre-rotation Vanes and Discharge Valve can

be manually controlled. This screen also serves as a

gateway to subscreens to calibrate the Pre-rotation

vanes and Proximity Probe.

Requires login access level of SERVICE.

DISPLAY ONLY
Oil Pressure

Displays the pressure differential between the Pump

Oil Pressure transducer for the compressor and the

common Sump oil pressure transducer. If either of

these transducers are out of range, the display field

will show XX.X PSID. The displayed value includes

the offset pressure derived from auto-zeroing during

the system pre-lube period. The offset pressure is the

pressure differential between the compressor Pump

Oil Pressure Transducer and the Sump Oil Pressure

transducer outputs during a three (3) second period

beginning ten (10) seconds into the system pre-lube

period. During this time, the transducers are sensing

the same pressure and their outputs should indicate

the same pressure. However, due to accuracy toler-

ances in transducers, differences can exist. Therefore,

to compensate for differences between transducers and

assure differential pressure sensing accuracy, the off-

set pressure is subtracted algebraically from the dif-

ferential pressure. The offset pressure calculation is

not performed if either transducer is out of range. The

offset value is taken as 0 PSI in this instance. If one

compressor is already running when bringing on the

second compressor, the offset calculation used will be

that which was calculated during the first compressor

pre-lube.

Oil Sump Temperature

Displays the temperature of the oil sump.

Discharge temperature

Displays the discharge temperature.

High Speed Thrust Bearing Proximity

Differential

Displays the distance between the high speed thrust

collar and the tip of the Proximity Probe for compres-

sor #1. This measurement takes into account the refer-

ence position established at the time of chiller manu-

facture.

COMPRESSOR 1 OR 2 SCREEN

LD27849

FIGURE 10 -

COMPRESSOR 1 SCREEN

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды