background image

5803641-JIM-B-0620

2

Johnson Controls Ducted Systems

General

Johnson Controls J**ZJ units are single package air 
conditioners with optional gas heating designed for outdoor 
installation on a rooftop or slab and for non-residential use. 
These units can be equipped with factory or field installed 
electric heaters for heating applications.

These units are completely assembled on rigid, permanently 
attached base rails. All piping, refrigerant charge, and electrical 
wiring is factory installed and tested. The units require electric 
power, gas supply (where applicable), and duct connections. 
The electric heaters have nickel-chrome elements and utilize 
single-point power connection.

Safety Considerations

This is a safety alert symbol. When you see this symbol 
on labels or in manuals, be alert to the potential for 
personal injury.

Understand and pay particular attention the signal words 

DANGER

WARNING

 or 

CAUTION

.

DANGER

 indicates an 

imminently

 hazardous situation, which, 

if not avoided, 

will result in death or serious injury.

WARNING

 indicates a 

potentially

 hazardous situation, which, 

if not avoided, 

could result in death or serious injury.

CAUTION

 indicates a potentially hazardous situation, which, if 

not avoided 

may result in minor or moderate injury.

 It is also 

used to alert against unsafe practices and hazards involving 
only property damage.

Due to system pressure, moving parts, and electrical 
components, installation and servicing of air conditioning 
equipment can be hazardous. Only qualified, trained service 
personnel should install, repair, or service this equipment. 
Untrained personnel can perform basic maintenance functions 
of cleaning coils and filters and replacing filters.

Observe all precautions in the literature, labels, and tags 
accompanying the equipment whenever working on air 
conditioning equipment. Be sure to follow all other applicable 
safety precautions and codes including ANSI Z223.1 or CSA-
B149.1- latest edition.

Wear safety glasses and work gloves. Use quenching cloth and 
have a fire extinguisher available during brazing operations.

Improper installation may create a condition where the 
operation of the product could cause personal injury or 
property damage. Improper installation, adjustment, 
alteration, service or maintenance can cause injury or 
property damage. Refer to this manual for assistance or 
for additional information, consult a qualified contractor, 
installer or service agency.

This product must be installed in strict compliance with 
the installation instructions and any applicable local, 
state and national codes including, but not limited to 
building, electrical, and mechanical codes.

Before performing service or maintenance operations on 
unit, turn off main power switch to unit. Electrical shock 
could cause personal injury. Improper installation, 
adjustment, alteration, service or maintenance can 
cause injury or property damage. Refer to this manual. 
For assistance or additional information consult a 
qualified installer, service agency or the gas supplier.

This system uses R-410A Refrigerant which operates at 
higher pressures than R-22. No other refrigerant may be 
used in this system. Gage sets, hoses, refrigerant 
containers and recovery systems must be designed to 
handle R-410A. If you are unsure, consult the equipment 
manufacturer. Failure to use R-410A compatible servicing 
equipment may result in property damage or injury.

If the information in this manual is not followed exactly, a 
fire or explosion may result causing property damage, 
personal injury or loss of life.
Do not store or use gasoline or other flammable vapors 
and liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
a. Do not try to light any appliance.
b. Do not touch any electrical switch; do not use any 

phone in your building.

c. Immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions.

d. If you cannot reach your gas supplier, call the fire 

department.

Installation and service must be performed by a qualified 
installer, service agency or the gas supplier.

Содержание J ZJ Series

































































Отзывы: